Puratek Auto Level Controller Giveaway only on Reef2Reef!

[revhtree]

Puratek Auto Level Controller Giveaway!
Sponsored by our newest R2R sponsor Puratek

How to Enter:
1. Visit the Puratek website and post back here in this thread what features you like about any of their products. Click Here
2. LIKE the Puratek FACEBOOK page here: PURATEK FACEBOOK PAGE
3. Smile and hope you win!

Drawing
On Dec. 5th we will pick one winner by random draw from this thread and the winner will be verified to have completed all requirements including a facebook check.

The Prize
The name drawn will receive brand new Puratek Auto Level Controller shipped to their door valued at over $230.00!

The Auto Level Controller, an Auto Top-Off system, is an ideal addition to any aquarium system. It is natural for water to evaporate on a daily basis and requires constant attention to maintain proper water levels. If not maintained on a regular basis in saltwater systems, the salinity will rise as the water evaporates because salt will not evaporate. These fluctuations in salinity can cause undue stress to your inhabitants.Using an auto top off system alleviates the daily activity of having to add fresh water on a regular basis. Performing this aquarium husbandry is a tedious, unrewarding task and can leave you in despair if not done properly.

This modern approach to auto level controlling is ground breaking to the industry and offers features never seen before in such an important piece of equipment seldom overlooked. Read More Here

Features

Maintains consistent salinity
Non-intrusive sensors that attach to outside of aquarium or sump so no worry about sticky or leaking mechanical sensors. Also snails or crabs will not interfere with operation
85 dB Audible alarm to notify of abnormal high or low water level or if the maximum water make up time has been exceeded
Standby switch – Temporarily disable level control while performing maintenance; for example, water changes or cleaning that could false trigger sensors
Alarm reset/program mode switch – silence alarm or initiate program to allow custom settings for max run time, hysteresis and level sensor selection
Supports up to four level sensors for normal (makeup control), low, high and top-off reservoir levels
Controls top-off water pump in makeup water reservoir or solenoid valve for connection directly to R/O filtration system
Low voltage 12VDC control for safety and low power consumption
Programmable max-run-timer counters to prevent top-off water running too long in the event sensor fails
Programmable hysteresis setting to control time delays in activating alarms or control due to water ripple or other disturbances in the water that could cause false alarms or control
Status LED for each level sensor for easy sensor status and program mode indicators
Processor controlled to maximize flexibility and expandability in feature offering and upgrades
Interfaces to Insight 24/7 Monitor/Controller for complete system integration for…
Audible and remote email alarming
Maximize system control in the event water levels are incorrect – shut pumps or chillers off to prevent damage
Notifications of when top-off water is being added
Keep log of how often top-off water is being added
Perform firmware upgrades

Thanks again to Puratek.com!
Puratek Reef2Reef Forum

 

[Ericsch333]

Fully Programmable and you can upgrade the firmware

Facebook page liked

 

[joseserrano]

I like that it is an alternative controller. If there is no competition the controllers will not advance as quickly as they are actually able to.

 

[saltyphish]

1. I like that the products are made in the U.S.A. and looking at the ATO unit, it has no moving parts and does not need to be inserted in the water to work I am intrigued. I like the possibilities with this unit. 2. facebook page liked.

 

[lviva003]

[FONT=Helvetica Neue, Arial, Helvetica, Geneva, sans-serif]The fact that the sensors never come in contact with the water! I definitely need me one of this. Thanks for the opportunity.[/FONT]

 

[DRThompson]

Non-intrusive sensors that attach to outside of aquarium or sump so no worry about sticky or leaking mechanical sensors. Also snails or crabs will not interfere with operation

FB liked

 

[mr_bigl]

I like that it doesn't have to be submerged which will decrease the chances of failure.

FB paged liked!

 

[Kworker]

I like the fact they have apps that I can use to monitor the tank while away!

Liked on Facebook..

 

[jasonp87]

I like that you can put the unit in standby mode while doing water changes and other maintenance that may falsely trigger the top off unit.

Facebook page liked!

 

[jkef2010]

I like that the inhabitants can't interfir with it at all. As well as being able to be monitored from afar.

Facebook liked. Thanks good luck everyone.

 

[Greenstreet.1]

To bad I don't use face book. I love that you are able to program and control it. Will look into it for my next setup.

 

[Matthias7]

The website looks awesome and is easy to navigate. The standby feature on the ATO is a great idea. Would be nice not to have to unplug every time I am working in the sump.

 

[c_healy]

Love that it's out of the water.


Liked on FB.


Thanks!

 

[SkipperTheSohalTang]

I love how you can run it straight to the RODI! FB page liked

 

[revhtree]

Bump!

 

[Mike J.]

I like Standby switch – Temporarily disable level control while performing maintenance; for example, water changes or cleaning that could false trigger sensors. Also like the sensor doesn't go in the water.
Like on Facebook, too. My current auto top off sensor fails all the time. Been looking into getting a different one.

 

[mike007]

Looks like a affordable easy to use controller.

 

[Joker79]

Liked on Facebook! Been liked for a while now Love the fact that the sensors will not be exposed to the salt build up, possibly rusting, ect!!!
I've been looking at an ATO for my setup and this would be a great score!
Good luck to everyone and thank you for putting this giveaway together!!!
:rockon:

 

[RandoReefer]

Out of water sensors are a great idea. Even the sensor of my current ATO gets crusted and fails. Love the controller that tells you how much water you replace during a day's evaporation. Really allows you to dial in kalkwasser dosing through ATO.

 

[Steelerfan747]

Facebook liked. Love the fact that the ATO sensors do not have to be on water. :bigsmile: ing and waiting for Dec 5th