Are my tanks seams beginning to fail?

Jimbo327

Well-Known Member
View Badges
Joined
Jun 12, 2007
Messages
510
Reaction score
531
Location
Orange County, CA
Rating - 0%
0   0   0
Update: Red Sea has informed me they will be sending me a new Reefer 250 G2+
If funds are not an issue, I would sell that replacement tank and find yourself a different brand tank. Not worth the headache of doing this again in a few years.

And I'm surprised your tank didn't blow out with that much sand in the seams! Very very lucky.
 

PharmrJohn

The Dude Abides
View Badges
Joined
Mar 19, 2019
Messages
3,040
Reaction score
6,953
Location
Shelton, Washington
Rating - 0%
0   0   0
In terms of new tanks, take a look at Glass Cages. They are priced higher than what is considered standard, but they are quality products. And you can basically build your own tank. Talk to @Joe Glass Cages for more info. I'm going this route when I finally buy into the hobby.
 
OP
OP
StevenL

StevenL

Community Member
View Badges
Joined
Feb 15, 2023
Messages
45
Reaction score
151
Location
NY
Rating - 0%
0   0   0
If that's the best the law allows I guess you have no choice.
I'd be demanding money back.

But, I guess you could sell it as a reptile tank or something.
I didn’t buy it from Red Sea directly and the LFS that sold it to me didn’t do anything wrong so I’m not sure a refund is an option. I think this is the best case scenario given the situation so I’m content with the outcome.
 

buruskeee

Well-Known Member
View Badges
Joined
Aug 17, 2023
Messages
822
Reaction score
552
Location
Sacramento
Rating - 0%
0   0   0
If that's the best the law allows I guess you have no choice.
I'd be demanding money back.

But, I guess you could sell it as a reptile tank or something.
I’m not sure there is any company that will refund something 2 years after purchase when they have a warranty to cover the issue by replacement. If there is such a company in existence, please point me to them because I will only buy from that company, as that’s one heck of a refund policy.
 

buruskeee

Well-Known Member
View Badges
Joined
Aug 17, 2023
Messages
822
Reaction score
552
Location
Sacramento
Rating - 0%
0   0   0
Yes reefer 250 serial# >30,500. I am hoping the G2 is better constructed
Yeah, they did quite a bit, a lot of it is structural with the stand too. I’d ask them about if there was any changes to the stand for the G2 for your model.

Haven’t really seen a G2 failure aside from chips and glass breaking from handling the tanks.

My LFS also has a few “brand new” G1 they’re trying to offload. I wouldn’t touch a G1 tank period - they really cut a ton of corners with that generation.
 

Tamberav

10K Club member
View Badges
Joined
Jul 4, 2014
Messages
10,968
Reaction score
16,488
Location
Duluth, MN
Rating - 0%
0   0   0
Yes reefer 250 serial# >30,500. I am hoping the G2 is better constructed

I hate to give you nightmares... here is a G2 - ha! This is probably the tank @BristleWormHater was thinking of..

you could always eurobrace the bottom and/or top.

 

buruskeee

Well-Known Member
View Badges
Joined
Aug 17, 2023
Messages
822
Reaction score
552
Location
Sacramento
Rating - 0%
0   0   0
Sorry... I must have been thinking of a different red sea failure thread, there's been like three this week:grinning-face-with-sweat:.
There’s another thread titled “G2” but in the thread they tried to correlate a G1 V3 as G2 because it has G2 “features”. From what I’ve seen (or haven’t seen from lack of failure), the G2 corrects a lot of the G1 mishaps. It’s a shame they didn’t cut manufacturing of G1 quicker.
 

BristleWormHater

2500 Club Member
View Badges
Joined
Jul 4, 2024
Messages
2,875
Reaction score
3,714
Location
Roswell, GA
Rating - 0%
0   0   0
Yeah, they did quite a bit, a lot of it is structural with the stand too. I’d ask them about if there was any changes to the stand for the G2 for your model.

Haven’t really seen a G2 failure aside from chips and glass breaking from handling the tanks.

My LFS also has a few “brand new” G1 they’re trying to offload. I wouldn’t touch a G1 tank period - they really cut a ton of corners with that generation.
Can't be trusted don't care what Red Sea says
 

buruskeee

Well-Known Member
View Badges
Joined
Aug 17, 2023
Messages
822
Reaction score
552
Location
Sacramento
Rating - 0%
0   0   0
I hate to give you nightmares... here is a G2 - ha! This is probably the tank @BristleWormHater was thinking of..

you could always eurobrace the bottom and/or top.

That’s not a G2. You can tell by the black gate valve and single return nozzle.
 

bossman818

Active Member
View Badges
Joined
Mar 26, 2024
Messages
162
Reaction score
140
Location
canyon country
Rating - 0%
0   0   0
I have a XL300 G1 and I cut this 1 1/2 inch plywood to place under tank. I believe the issue is the front glass not being supported by stand. Somehow it’s still holding on and crossing my fingers it holds forever. I am very paranoid though.
 

Attachments

  • 74599719312__69EDB387-508D-4461-8265-831B86480EF0.jpeg
    74599719312__69EDB387-508D-4461-8265-831B86480EF0.jpeg
    94.5 KB · Views: 47

TOP 10 Trending Threads

Back
Top