DIYreefer's DIY 100g AIO frag tank

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
Hello everyone,

The time has come to start a thread for my most recent frag tank build. This one is a bit different than most, being that it's made out of plywood and epoxy and is essentially a rather large AIO (no sump). I built this tank with the intent of growing out corals to sell/trade in order to support my addiction... I mean, hobby. However, my main objective was to keep it VERY simple and make it as ergonomic as possible, while still being functional Hence the AOI aspect... no bending over under a stand to work on anything in a sump :). The tank has been set up for approximately 2 months and has been holding a few corals for about a week now. So far, so good.

The specs are as follows:

Dimensions - 7'x30"x1' w/ the display area being 5'10"
Lighting - 10 x 50w Nicrew Hyperreef LEDs daisy chained together and controlled via a nicrew controller (kessil knock off), and 4 x 54w T5s (1 coral plus, 3 blue plus)
Flow - Jeboa PP20 does the brunt of the work while a pair of Jeboa DCP-5000s (one is the return pump, one feeds my UV sterilizer) that provide a small amount of supplemental flow
Filtration - Aquamaxx DFC-120 skimmer, 4l of Seachem biomatrix (seeded from my display tank), a little bit of activated carbon, and a 36w Jeboa UV sterilizer
Temperature control - 300w heater, and a desk fan that turns on in conjunction with the T5s (although I may soon be ditching the heater, I think the added heat from the UV sterilizer may be adequate in keeping the temp stable around 79*).

Inhabitants will be ever evolving based upon whatever I'm into at the moment. It's been a few years since I have taken coral photos so I'm a bit rusty with the camera, but here are a few pictures of the set up and a couple of the corals that I have moved over from my display tank. If anyone has any questions feel free to ask!
Jack o lantern lepto
IMG_1155.JPG

Nightmare plays
IMG_1156.JPG

Bowsers.. These guys weren't getting enough light in my display tank. Should color up fine in the frag system.
IMG_1157.JPG

Awesome Blossoms. As you can see, I've got some work ahead of me, trimming all of this stuff that has grown onto the rack.
IMG_1158.JPG

Wee little WD nublet. I'm almost embarrassed that I actually glued this thing to a frag plug, but it made for a good candidate to test out the SPS viability in the new tank.
IMG_1161.JPG

Little baby JB, about the size of a dime.
IMG_1163.JPG

WWC Tazers. Excellent growers for me, and absolutely bulletproof. You could grow these guys pretty much anywhere, IME. Should color up better now that they're in more adequate lighting.
IMG_1164.JPG

Rastas
IMG_1165.JPG

Grafted purple/red plating monti
IMG_1167.JPG

Pink Kraks
IMG_1173.JPG

And finally, the tank...
IMG_1177.JPG IMG_1182.JPG IMG_1180.JPG IMG_1176.JPG IMG_1179.JPG IMG_1174.JPG IMG_1175.JPG

I'll post more pictures as I move things over from my display.
 
Last edited:
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
I personally would love to see and hear about your process for sealing the plywood...

I used pond armor.... 1.5g of it! I realistically only needed probably half of what I used but I sleep better at night knowing that this thing is sealed SOLID! In addition to going overboard with the epoxy, I also laid 2 layers of 8 ounce fiberglass cloth on the bottom and on all seams. Built to last, lol.
 
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
Did you seal all sides of the wood?

Definitely looking forward to the process pics.

Are you referring to inside the seams of the individual panels? If so, no. I've used pond armor in a similar fashion (although not quite as over built) with no problems in the past. Pond armor is well worth the expense as it makes for a very solid, and reef safe seal. Honestly, I trust it more than I do traditional glass or acrylic tanks. I probably could have built a similar tank in either glass or acrylic for around the same cost but this thing is bullet proof. I don't have any concern what so ever about a seam ever bursting or glass/acrylic breaking. My only concern would have been something cutting through the epoxy but with it being probably 10x's the necessary safe thickness, that isn't much of a concern.

So I thought that I had more pictures than I do, but I tend to get so I to my projects that I forget to document them most of the time. Anyway, here's a few...

The tank is constructed out of 3/4" cabinet grade plywood. Except for one panel that is plain 3/4" sanded pine plywood (I'm too cheap to buy another $100 sheet of plywood for 1 small panel lol)
20220323_165223.jpg

I cut the overflow slits with a 1/4" dado blade in my table saw. Due to the curve of the blade there is a natural slant that allows the water to flow smoothly down into the skimmer chamber. Purely coincidence, but definitely an added bonus as this makes the overflow much quieter.
20220323_124614.jpg

20220323_152945.jpg 20220323_125248.jpg

Mistakes were made :(. Given that I was using 3/4" material, I knew that I would have a hard time using anything (pumps, food clips, etc.) that required a magnet to hold it in place. My solution... use 1/2" material that had an additional layer around the edges to allow for better magnetic grip. This would have worked perfectly fine, had I not installed the 1/2" panel on the wrong end of the tank... oops! 20220323_153141.jpg

My solution to this was to throw a little tantrum, regroup, and figure out a new plan. The end result was to use a router to remove 1/4" of material out of the panel that needed to be 1/2". It's not my finest woodworking or tank building moment, but it ended up working. Granted, I had to stand the 7' long tank up on it's end and stand in the bed of my truck to do the job, but who doesn't like a little challenge every now and then?

20220324_100032.jpg 20220324_104002.jpg 20220324_112914.jpg

And after a little spackle and some sanding to remove the residual small gouges left by the router, problem solved! But yeah, I'm still not proud...
20220324_113657.jpg

Just a couple more random pictures of the build process. I forgot to mention, the entire top of the tank is braced with 3/4"×1 1/2" poplar hardwood. This wasn't really necessary, structurally, but I didn't want to have the brittle edges of the plywood taking the abuse of the inevitable dropped objects, people leaning on it, etc... even with it being coated in epoxy. Although unnecessary, this step simply gives me peace of mind as well.

20220323_191725.jpg 20220323_191715.jpg

I wish I had more pictures of the epoxy process but the workable time (in my climate) is only about 20 minutes... maybe 30 TOPS before it starts setting up. And at roughly $300 per gallon, pictures were definitely not my priority at the time, lol. 20220327_202545.jpg
20220328_115844.jpg

Unfortunately these are the only 2 pictures I took but there is a great tutorial on YouTube that shows how to use pond armor for this application. I believe the guy goes by "king of DIY", or something similar to that. I know his videos are quite popular so I'd imagine that anyone that stumbles upon this thread likely already knows who talking about.

One thing I would add that I haven't seen previously, is how I measured out and mixed the 2 individual parts. After my first coat I quickly realized that there were going to be parts of the epoxying process that would be more intricate (between the overflow slits, up underneath the edges of the top trim pieces, etc.), and in turn would require much smaller amounts of epoxy. As previously mentioned, pond armor is not cheap, so I wanted to cut my waste to a minimum. I did this by using a pair of 1,000ml syringes (found them on amazon). This allowed me to mix up much smaller batches, accurately. I used one syringe for part A, and the other for part B, never mixing them up allowed me to use them over and over. I don't recall this being mentioned in the YouTube videos but it proved to be invaluable for me.

So besides not mentioning that I used 3" deck screws placed 3" apart around the entire perimeter of the tank, false wall, and overflow baffle and using wood glue on all joints, that pretty much sums up the build. If I missed something and anyone has any questions, I'll happily answer. I'll be posting more pictures as I move over more growout frags/colonies from my display tank in the coming days/weeks. Thanks!
 
Last edited:
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
Here are a few pictures of when I first got the tank on the stand (stand is also 3/4" plywood), and a couple from when I was adding the finishing touches to the epoxy. 20220420_095729.jpg 20220420_111214.jpg 20220420_122448.jpg 20220420_122502.jpg 20220420_122508.jpg 20220420_122546.jpg

As you can see in the last picture, the tank doesn't sit flush with the edges of the stand. That would be because I'm an idiot, and somehow built the stand 1" longer than it should have been. This is the result of a "measure once, cut once" woodworking philosophy, lol. This enrages my OCD, but structurally it still works and holds the weight of the tank perfectly fine.
 
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
I plan to continue moving corals over to this tank on. a daily basis so long as everything continues to do well. Here are the two that I moved over last night.

Tropic Thunder monti
IMG_1190.JPG

Pink Kraks
IMG_1189.JPG

I forgot to mention, I do have a couple of fish in the tank, a tiny little 2.5" Naso tang and a 1.5" six-line wrasse. Once they get used to me and aren't so skittish I'll try to get a couple pictures of them as well.
 
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
Added a few more last night.

WWC AOI
IMG_1194.JPG

Awesome Blossoms
IMG_1195.JPG

SBB Hephaseu...whatevers
IMG_1196.JPG

Mind Tricks
IMG_1197.JPG

Exospheres
IMG_1198.JPG

HR Death Stars
IMG_1199.JPG

Another WD nub
IMG_1200.JPG

TGC Cherry Blossom This one is a stunner under all blue lighting, kinda meh under full spectrum.
IMG_1201.JPG

WWC Grafted Cap
IMG_1205.JPG
 
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
I got my Jawbreaker garden moved over. I started with 15 or 16 polyps back about 8 or 9 months ago and now have precisely 145! As I moved them over I counted all of them. Most of which are still underneath the larger ones, but I expect they will move around and drop babies as well. I'll probably start trading/selling some of these soon.

IMG_1221.JPG

IMG_1222.JPG

A couple already have green coming in :)
IMG_1234.JPG
IMG_1235.JPG

Nice red coverage on this little guy. There's another one that similar buried in there somewhere as well.

IMG_1233.JPG

I also took some "blue light special" photos. Definitely still need to get the hang of that.

TGC Cherry Bomb under all blue LED
IMG_1241.JPG

WD nub under all blue LED
IMG_1242.JPG

SBB Hephasnuffulfuagouses under all Blue LED
IMG_1243.JPG

HR Death Stars.. all blue LED
IMG_1244.JPG

Awesome Blossoms, all blue LED
IMG_1245.JPG
 
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
Fragged some zoas yesterday. If all goes well I should be ready to sell/trade some in a couple weeks :)
IMG_1346.jpeg

And 24 hours later, not looking too bad!
IMG_1352.jpeg
 
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
Had a few minutes to spare so I snapped some pics of a couple of the new zoa frags and also a few of the acros that I clipped and moved over from my main system.

The tank has overall been running well, but it's a little nutrient deficient with only 5 small fish in approximately 100g. I think I need to add a few more fish and start feeding a bit heavier.

WWC Tazer
IMG_1370.jpeg

Hephasteus IMG_1371.jpeg

Awesome Blossom that overgrew a frag plug base
IMG_1372.jpeg

Fairy Farts
IMG_1374.jpeg

Rastas
IMG_1376.jpeg

AOI IMG_1377.jpeg

Jack-o-lantern lepto
IMG_1386.jpeg

Pinky The Bear
IMG_1387.jpeg

Pink Caddy
IMG_1388.jpeg

Cali Tort
IMG_1389.jpeg

Master Yoda
IMG_1390.jpeg

TSA Something... I don't remember
IMG_1391.jpeg

Oregon Tort
IMG_1392.jpeg

Pikachu... I've had this frag for nearly a year and it never did anything in my display tank. Happy to see it encrusting and starting to show polyp extension in the frag tank.
IMG_1395.jpeg

Jawbreakers. A few still need to color up, but my collection of these guys are really loving the new tank. They are spreading rapidly and I should be able to sell/trade about 10 per month while still maintaining a colony of 100 or so. They really do grow that fast.
IMG_1398.jpeg

That's it for now. I want to document the progress of these acros, so posting them here to start a data log.
 
OP
OP
DIYreefer

DIYreefer

Well-Known Member
View Badges
Joined
Oct 27, 2020
Messages
674
Reaction score
980
Location
Tx
Rating - 100%
10   0   0
Snapped a few pics from around the frag tank today. So much has changed since the last time I posted!

_MG_4671.JPG

_MG_4672.JPG

_MG_4673.JPG

_MG_4674.JPG

_MG_4675.JPG

_MG_4676.JPG

_MG_4677.JPG

_MG_4678.JPG

_MG_4679.JPG

_MG_4680.JPG

_MG_4681.JPG

_MG_4682.JPG


_MG_4683.JPG

_MG_4684.JPG

_MG_4685.JPG

_MG_4687.JPG

_MG_4688.JPG


_MG_4691.JPG

_MG_4692.JPG

_MG_4693.JPG

_MG_4694.JPG

_MG_4695.JPG

_MG_4696.JPG
 

Mastering the art of locking and unlocking water pathways: What type of valves do you have on your aquarium plumbing?

  • Ball valves.

    Votes: 66 51.6%
  • Gate valves.

    Votes: 67 52.3%
  • Check valves.

    Votes: 32 25.0%
  • None.

    Votes: 29 22.7%
  • Other.

    Votes: 9 7.0%
Back
Top