Laser cut anything you need acrylic/wood etc.

[Bronx_Discuss]

Hi guys,

Let me know if you need anything laser cut out of a sheet of acrylic. I can work with you to make boxes, racks to your specs. Max dimension for now is 11x18 for now. I just need a little time to source the sheets of acrylic before fabrication. Most common easy access thickness is 1/8, 1/4. I would need time to work with you but I can do it. I can do assembled pieces or if you want to glue them yourself I can just cut the sheets. Let me know.

 

[Bronx_Discuss]

Hey guys. I can now cut as long as you need only limitation is about 20 inches in width or length depending on how you look at it. The issue is really shipping rate for a huge project but if you are local to NY, we can really get something going that’s huge. PM me if you have a project you want to do on a laser cutter. If you have a design already made and just need stuff cut, reach out and we can work together to proof it and cut it to your design. Thanks

 

[Pete Luna]

Whats the cost of a 11.5 X 18.5 X 1/4” Black with over flow slits 12” long center top. Need it to divide my frag tank

 

[galantra]

Can you make inlet panel for triton trigger sump?

 

[Bronx_Discuss]

Sure. Can you draw me the dimensions and hole diameters and distances from each other? Simple drawing is fine I can send you a final drawing for you to verify before I cut. What thickness size acrylic you are looking for color preference? I may have several colors based on sizes. Let me know, we can work on this. Please PM me.Thanks

 

[Galiant50]

Are you still doing this? How much would a 17"x8"x1.5" internal overflow box be?

 

[Bronx_Discuss]

Hey. I am. I’ll PM you. I am awaiting my new Sanding machine to arrive so may take a few days. But yes I can take this on.

 

[ShaneWedge]

Wish I had seen this post before I posted this

 

[Bronx_Discuss]

PM me I can help you with this project if you still need it. I’m not a master but I have done a few. LoL. Thanks

 

[jose hernandez]

not sure if i contacted you but im interested in a cabinet to oragnize all of my equipment

 

[Bronx_Discuss]

Yeah. I’m open to do your project. pm me with specs and we go from there. I’m a bit short on acrylic but I can drive to the city to pick up what you need. I’ll need to order hinges and stuff but PM me I can help you with this.

 

[jose hernandez]

K will get specs 2morrow

 

[Frozen Tundra Reef Dreams]

do you have fluorescent orange or fluorescent blue acrylic? nd which thickness. I need couple different things.done

 

[Bronx_Discuss]

PMd you sir. Thanks for reaching out

 

[GuppyHJD]

Bronx_Discuss,
I am looking for a ATO container - 5" deep, 16" high, and 20" wide...preferably with a lid. Is this something you can do?

 

[Bronx_Discuss]

I can do it but it won’t look like a triton. Probably not cost effective but it will be exactly the specs you want. Just being honest and setting expectations. I’m more of a mushroom box maker and stuff like sump baffles and things.

 

[Russell G]

I have a relatively easy one for you. I need a stand for my skimmer so I can run it externally. I’m looking for the stand to be a simple box made from black acrylic with dimensions of 7.25” wide x 12.5” long x 3.75” tall.

The height must be the exact outside dimension but the others have some leeway. If the height isn’t correct, the output from the skimmer won’t clear the rim of the sump correctly or it will be too tall to remove the skimmer cup.

Let me know what you think and we can go from there.

 

[Bronx_Discuss]

Some of the stuff I made this week. Again, the quality is good it’s my hobby and I spend time on it because I care and enjoy it.

 

[Russell G]

I want to thank you for the work you did for me!

I had him make me a skimmer stand and a overflow cover and they both turned out perfect! I needed to raise the skimmer to clear the edge of my sump to run it externally and it was built exactly to spec and the overflow cover is made better than the overflow itself. I just gave
him the specs for the pieces and he did a great job communicating throughout the entire process.

I highly recommend him for any custom pieces you may need!

 

[Bronx_Discuss]

Thank you for your support and feedback. Really had fun making this for you and contribute to your system. I feel like I’m part of your project. Please keep in touch and show how your whole system looks when it’s all said and done. Anything you need done big or small let me know, I’ll work on it.