I was contacted earlier this week and RedSea confirmed my address for the parts shipment.
that is nice of them I hope I get that soon.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
I was contacted earlier this week and RedSea confirmed my address for the parts shipment.
What about doing it beforehand if you have a tank that you haven't added water to yet?I would be cautious with taking matters into your own hands in regards to making your own vertical braces.
If the support is too long, you could create a new stress point. Even if the support is perfect length, wedging it in place will temporarily bow the plywood the opposite direction.
Make no mistake, propping up a sag point that is bearing a load is already a concern. It's quite possible that relieving the stress from a pressure point may prove to be counter productive, I personally can't wait to learn how they propose to fix the problem.
I'm sure their engineers are fully aware of the risks involved. I would be surprised if they don't suggest removing at least a portion of the water before attempting to add the retrofit. Ideally it would be a no brainer to remove all the water but RS is stuck between a rock and a hard place.
NO away - it will void the warranty - and no just dontWhat about doing it beforehand if you have a tank that you haven't added water to yet?
I was told by State Farm, Farmers, and Progressive that damage done to the home as a result of a failed tank IS NOT covered. This is in California. I called several times and asked to speak to supervisors, etc. All the answers were the same. Said you'd be hard pressed to find someone who does cover it. Maybe this varies from state to state as I know some people have had damage and their insurance companies take care of them. Lot of conflicting information on the internet.This has been discussed a couple times - Homeowners insurance (not flood insurance) will cover damage from the water - not the livestock/rock/etc - if there is a sudden failure... BUT - this is also company dependent - some insurance companies do not cover aquarium damage at all - or unless you have a 'rider'
Yes I know. Travelers covers it in mn. Only the property damageI was told by State Farm, Farmers, and Progressive that damage done to the home as a result of a failed tank IS NOT covered. This is in California. I called several times and asked to speak to supervisors, etc. All the answers were the same. Said you'd be hard pressed to find someone who does cover it. Maybe this varies from state to state as I know some people have had damage and their insurance companies take care of them. Lot of conflicting information on the internet.
I would set it up and enjoy it.Man, I have a 625 that I was about to fill over the next couple of weeks. Now I am nervous to continue. I wonder if it would be worth just building my own stand and not have to worry about the reefer stand failing over time.
What would you guys do?
Man, I have a 625 that I was about to fill over the next couple of weeks. Now I am nervous to continue. I wonder if it would be worth just building my own stand and not have to worry about the reefer stand failing over time.
What would you guys do?
I was told we would have them at the end of this month at the earliest.that is nice of them I hope I get that soon.
The 625 has no reported issues, to my knowledge.
In the future I personally will be building my own stands and ordering custom tanks. These ready-to-go setups are nice, but after doing some research, I don’t think I would do it again. The materials used are really the bare minimum to support them.
Why would you do that? Why are you nervous - this 'defect' affects a very small percentage of the 750's - and doesnt affect the other models at all. If you do go this way - make sure that building your own stand doesn't void the warranty.Yea, that's kind of what I'm thinking as well. I could sell the 625 and just go that route the first time.
Why would you do that? Why are you nervous - this 'defect' affects a very small percentage of the 750's - and doesnt affect the other models at all. If you do go this way - make sure that building your own stand doesn't void the warranty.
A. You do not know the exact numbers of what and how many are effected.Why would you do that? Why are you nervous - this 'defect' affects a very small percentage of the 750's - and doesnt affect the other models at all. If you do go this way - make sure that building your own stand doesn't void the warranty.
I guess I'm just being paranoid.
A. You do not know the exact numbers of what and how many are effected.
B. The number of 625s sold compared to 750s is much smaller. So there is no real sampling of 625 failings. None have been publicly reported that I can find.
Without any published numbers from RedSea everything is 100% speculation and assumption.
As a fellow 625 owner that has had their tank filled now for 4 months I will be always watching that seem. In time I might change things out. I won’t be trusting RedSea.. that much is one thing I can say with absolute conviction.
Hind sight is a wonderful thing. I don’t care about the warranty if the cheesy stand is going to cause a failure later. Build your own stand and be happy.. sell the entire set up and get something you can trust.. It’s up to the person.
You're probably being realistic - given the situation - But - I might consider calling RedSea and just talking to their customer service/technical people to get a better idea of what is going on.I guess I'm just being paranoid.
If you call Red Sea they will give you the exact numbers. (and the number is extremely small) - Now if you want to question that they are 'lying' - that (to me) would be paranoia.
You think a company will tell you failure rates if you "call them" ?
The 625 has no reported issues, to my knowledge.
In the future I personally will be building my own stands and ordering custom tanks. These ready-to-go setups are nice, but after doing some research, I don’t think I would do it again. The materials used are really the bare minimum to support them.
You think a company will tell you failure rates if you "call them" ?
That is certainly an.... interesting idea.