Cant figure out one problem with my VCA RFG

Users Who Are Viewing This Thread (Total: 1, Members: 0, Guests: 1)

Mombo

Well-Known Member
View Badges
Joined
May 2, 2017
Messages
593
Reaction score
251
Rating - 0%
0   0   0
Got my new tank all setup with the RFG's. Love em!

Im having a problem with placement though. So first problem was I turned my pump off to do some work and realized they were going to siphon out a TON of water.

So I raised em a bit. Now they will randomly (as there name predicted) shoots water towards the surface and makes enough ripples that it will actually pull air into it and shoot micro bubbles all over the place as well as make a strange sucking sound.

Trying to figure out what people are doing.
 

kinetic

Valuable Member
View Badges
Joined
Oct 22, 2009
Messages
1,273
Reaction score
941
Location
Albany, CA
Rating - 0%
0   0   0
Got my new tank all setup with the RFG's. Love em!

Im having a problem with placement though. So first problem was I turned my pump off to do some work and realized they were going to siphon out a TON of water.

So I raised em a bit. Now they will randomly (as there name predicted) shoots water towards the surface and makes enough ripples that it will actually pull air into it and shoot micro bubbles all over the place as well as make a strange sucking sound.

Trying to figure out what people are doing.

I had the same issue with mine. It would suck in air because the nozzle is too close to the surface and creates a vortex. I actually was never able to fix this issue. I know some people added segments of locline to push the nozzle further away from the surface of the water. So you might just have to keep the nozzle dipped down.

Behind the nozzle opening are the slots that should break the siphon at some point?

My pump is a DC pump (Reef Octopus VarioS-4) and I actually set it to only 8% power during feeding and light maintenance to keep the water at a standstill in the return drain, so it doesn't siphon. I did this by connecting it to my Apex Jr. with a VDM module. It's really nice, because the water level never drops.
 

Vivid Creative Aquatics

Upgrade Your Flow!
View Badges
Joined
Oct 12, 2017
Messages
1,520
Reaction score
2,172
Location
Phoenix, AZ
Rating - 0%
0   0   0
Got my new tank all setup with the RFG's. Love em!

Im having a problem with placement though. So first problem was I turned my pump off to do some work and realized they were going to siphon out a TON of water.

So I raised em a bit. Now they will randomly (as there name predicted) shoots water towards the surface and makes enough ripples that it will actually pull air into it and shoot micro bubbles all over the place as well as make a strange sucking sound.

Trying to figure out what people are doing.

@Mombo I should be able to help with this. Can you give me a bit more detail

- What size RFGs are you running?
- Approx how much flow (GPH) are you pushing through them?
- What size/type tank? Is it an All-in one, if so, what brand?
- If possible, can you post a pic of the nozzle installed from the side. I would like to get a better idea of how they are installed now.

Thank you!
 
OP
OP
M

Mombo

Well-Known Member
View Badges
Joined
May 2, 2017
Messages
593
Reaction score
251
Rating - 0%
0   0   0
I think I am making some progress. Ive been tuning my return pump flow down a bit and it has made the suction go away. So I could raise it a bit and now it doesn't over siphon the tank. Does the suction a little bit still now but I think I just to tune it a bit more.

Its a 120g SCA tank wtih 2 x 1/2in RFG's on it. I think I am pushing about 900gph through it now.
 

Vivid Creative Aquatics

Upgrade Your Flow!
View Badges
Joined
Oct 12, 2017
Messages
1,520
Reaction score
2,172
Location
Phoenix, AZ
Rating - 0%
0   0   0
I think I am making some progress. Ive been tuning my return pump flow down a bit and it has made the suction go away. So I could raise it a bit and now it doesn't over siphon the tank. Does the suction a little bit still now but I think I just to tune it a bit more.

Its a 120g SCA tank wtih 2 x 1/2in RFG's on it. I think I am pushing about 900gph through it now.
OK cool - is 900gph per nozzle or 900GPH for both - so aprox 450 each.

I'm going to setup it up on our Demo tank and run some tests so I can give you specific GPH and depths.
 
OP
OP
M

Mombo

Well-Known Member
View Badges
Joined
May 2, 2017
Messages
593
Reaction score
251
Rating - 0%
0   0   0
450 per nozzle. That is an estimate. I’m running a jebao 6500 at 60%. It does 1730gph at full power so at 60% it’s around 1000. Then it has about 5ft of 1in pipe and 2 elbows before it gets to a T pipe and goes down to 2x 1/2in nozzles. So I was guessing between 800 and 900 gph after all of that.

Could be less I’m not sure how to calculate all of that stuff
 

Vivid Creative Aquatics

Upgrade Your Flow!
View Badges
Joined
Oct 12, 2017
Messages
1,520
Reaction score
2,172
Location
Phoenix, AZ
Rating - 0%
0   0   0
450 per nozzle. That is an estimate. I’m running a jebao 6500 at 60%. It does 1730gph at full power so at 60% it’s around 1000. Then it has about 5ft of 1in pipe and 2 elbows before it gets to a T pipe and goes down to 2x 1/2in nozzles. So I was guessing between 800 and 900 gph after all of that.

Could be less I’m not sure how to calculate all of that stuff

Your calculations are close enough. :)

I ran some tests and at ~450gph and it looks like you should be able to get the base of the nozzle body (where the educators are located) to within about 1/2in of the surface of the water and have it not suck air. This of course may be effected if you have a wave maker in your system and the water level rises and lowers with the standing wave.

The syphon will break at approx. 3/4in where the accelerator portion of the nozzle is

The SCA 120 I looked up has dimensions of 48 x 24, so if we do the math, 48 x24 / 212, it looks like you have about 5.4 gallons per inch which puts this at about ~4gallons of water back into the sump when the main return pump is shut off. Depending on how big your sump is, they may or may not be an issue.

The lower the GPH the closer you can move those nozzles to the surface. Also - to help minimize the splashing you can point them down bit. The stream will exite the nozzle at about a 3o deg angles. So, if point them down about 20 degrees, then you still get surface agitation, but no splashing.

hope that helps and keep us posted as to your progress.

here are a few shots I took during the test

RFG050_0536.jpg



RFG050_0535.jpg
 
OP
OP
M

Mombo

Well-Known Member
View Badges
Joined
May 2, 2017
Messages
593
Reaction score
251
Rating - 0%
0   0   0
Thanks for all the help on this. I think ive got it figured out now. Once I tuned my return pump to the proper flow for my sump it was much easier to get everything set up correctly.
 

Vivid Creative Aquatics

Upgrade Your Flow!
View Badges
Joined
Oct 12, 2017
Messages
1,520
Reaction score
2,172
Location
Phoenix, AZ
Rating - 0%
0   0   0
Thanks for all the help on this. I think ive got it figured out now. Once I tuned my return pump to the proper flow for my sump it was much easier to get everything set up correctly.
Great! glad I was able to help. Be sure to post a pic of you tank when you get a chance to the RFG show-off thread :)
 

Huynhter_Soldier

Active Member
View Badges
Joined
Nov 19, 2016
Messages
259
Reaction score
88
Location
Clarksville
Rating - 100%
1   0   0
Great! glad I was able to help. Be sure to post a pic of you tank when you get a chance to the RFG show-off thread :)
Can you help me with my rfg? I have a single one with the adaptor for my red sea reefer 650. It would literally make vortex from the surface and shoot nothing but bubbles. I got it to stop for like a week but when i shut off my return, i had to raise the nozzle because of the back siphon. When I turned the return back on and pushed the the nozzles back down. Now, no matter what I do it still makes that stupid vortex. This thing is driving me crazy!
 

Vivid Creative Aquatics

Upgrade Your Flow!
View Badges
Joined
Oct 12, 2017
Messages
1,520
Reaction score
2,172
Location
Phoenix, AZ
Rating - 0%
0   0   0
Can you help me with my rfg? I have a single one with the adaptor for my red sea reefer 650. It would literally make vortex from the surface and shoot nothing but bubbles. I got it to stop for like a week but when i shut off my return, i had to raise the nozzle because of the back siphon. When I turned the return back on and pushed the the nozzles back down. Now, no matter what I do it still makes that stupid vortex. This thing is driving me crazy!
Sure - I'm sure we can get this figures out.

I'll need a bit more detail

- Post a pic of how you have it setup on your system.
A side profile pic would be best and provide the most info

- What pump are you running
If it's adjustable, at what percentage are you running it at?

- Whit size RFG Nozzles you running
1/2in, 3//4in or 1in? I'll likely be able to tell from the photo you will post, but it's good to confirm


Finally, take a look at this quick-start guide. i may help get you pointed in the right direction

RFG-Installation-Guidlines-1.jpg
 

Huynhter_Soldier

Active Member
View Badges
Joined
Nov 19, 2016
Messages
259
Reaction score
88
Location
Clarksville
Rating - 100%
1   0   0
Sure - I'm sure we can get this figures out.

I'll need a bit more detail

- Post a pic of how you have it setup on your system.
A side profile pic would be best and provide the most info

- What pump are you running
If it's adjustable, at what percentage are you running it at?

- Whit size RFG Nozzles you running
1/2in, 3//4in or 1in? I'll likely be able to tell from the photo you will post, but it's good to confirm


Finally, take a look at this quick-start guide. i may help get you pointed in the right direction

RFG-Installation-Guidlines-1.jpg
 

Attachments

  • 20220903_172939.jpg
    20220903_172939.jpg
    124 KB · Views: 113

Huynhter_Soldier

Active Member
View Badges
Joined
Nov 19, 2016
Messages
259
Reaction score
88
Location
Clarksville
Rating - 100%
1   0   0
Sure - I'm sure we can get this figures out.

I'll need a bit more detail

- Post a pic of how you have it setup on your system.
A side profile pic would be best and provide the most info

- What pump are you running
If it's adjustable, at what percentage are you running it at?

- Whit size RFG Nozzles you running
1/2in, 3//4in or 1in? I'll likely be able to tell from the photo you will post, but it's good to confirm


Finally, take a look at this quick-start guide. i may help get you pointed in the right direction

RFG-Installation-Guidlines-1.jpg
3/4" and maxspect jump 10k return. It doesn't matter what percentage I use it the nozzle continues to make that vortex.
 

Vivid Creative Aquatics

Upgrade Your Flow!
View Badges
Joined
Oct 12, 2017
Messages
1,520
Reaction score
2,172
Location
Phoenix, AZ
Rating - 0%
0   0   0
3/4" and maxspect jump 10k return. It doesn't matter what percentage I use it the nozzle continues to make that vortex.

Thanks for the photo. So that setup you have there really won't do well in a high-flow scenario. The Slip-Fit-Drop adapter is akin to a very short double 90deg. it also wont allow you to position the RFG parallel with the surface - which you will likly need to do at flow rates above 500 GPH

I would suggest if you have anything more than say 500-550 GPH going to setup that allows you to use a few segments of loc-lone or module hose so you can properly adjusted that RFG based on the amount of flow you can provide it.

Our CADE flow kits will fit the Red Sea Reefer series and come with a singe RFG, Module hose and the 25mm adapter.
They are also available in two sizes - 3/4in RFG and 1in RFG.
1662251895351.png


Since you already have the 3/4in RFG, you can also just pick up the adapter and loc-line, and use the existing RFG that you have. Both items are radially available at all the major online retailer as well as directly from our own website.

You'll need a 25mm to 3/4in Piep adapter (RSRLL075) and a few segments of 3/4in Loc-line hose. The hose comes in 6-segmetne stick but you'll only need two to 3 segments.

Once you have that, you'll be able to properly position the RFG to help mitigate the protentional for drawing in air. You will also get a much better randomized flow pattern -particular if you are supplying the RFG more than 500 GPH, since that Slip-Fit Drop is going to rob you of some of the throughput.
 

Huynhter_Soldier

Active Member
View Badges
Joined
Nov 19, 2016
Messages
259
Reaction score
88
Location
Clarksville
Rating - 100%
1   0   0
Thanks for the photo. So that setup you have there really won't do well in a high-flow scenario. The Slip-Fit-Drop adapter is akin to a very short double 90deg. it also wont allow you to position the RFG parallel with the surface - which you will likly need to do at flow rates above 500 GPH

I would suggest if you have anything more than say 500-550 GPH going to setup that allows you to use a few segments of loc-lone or module hose so you can properly adjusted that RFG based on the amount of flow you can provide it.

Our CADE flow kits will fit the Red Sea Reefer series and come with a singe RFG, Module hose and the 25mm adapter.
They are also available in two sizes - 3/4in RFG and 1in RFG.
1662251895351.png


Since you already have the 3/4in RFG, you can also just pick up the adapter and loc-line, and use the existing RFG that you have. Both items are radially available at all the major online retailer as well as directly from our own website.

You'll need a 25mm to 3/4in Piep adapter (RSRLL075) and a few segments of 3/4in Loc-line hose. The hose comes in 6-segmetne stick but you'll only need two to 3 segments.

Once you have that, you'll be able to properly position the RFG to help mitigate the protentional for drawing in air. You will also get a much better randomized flow pattern -particular if you are supplying the RFG more than 500 GPH, since that Slip-Fit Drop is going to rob you of some of the throughput.
But this was the kit that was made for the reefer? So I have to buy another one?
 

Huynhter_Soldier

Active Member
View Badges
Joined
Nov 19, 2016
Messages
259
Reaction score
88
Location
Clarksville
Rating - 100%
1   0   0
Thanks for the photo. So that setup you have there really won't do well in a high-flow scenario. The Slip-Fit-Drop adapter is akin to a very short double 90deg. it also wont allow you to position the RFG parallel with the surface - which you will likly need to do at flow rates above 500 GPH

I would suggest if you have anything more than say 500-550 GPH going to setup that allows you to use a few segments of loc-lone or module hose so you can properly adjusted that RFG based on the amount of flow you can provide it.

Our CADE flow kits will fit the Red Sea Reefer series and come with a singe RFG, Module hose and the 25mm adapter.
They are also available in two sizes - 3/4in RFG and 1in RFG.
1662251895351.png


Since you already have the 3/4in RFG, you can also just pick up the adapter and loc-line, and use the existing RFG that you have. Both items are radially available at all the major online retailer as well as directly from our own website.

You'll need a 25mm to 3/4in Piep adapter (RSRLL075) and a few segments of 3/4in Loc-line hose. The hose comes in 6-segmetne stick but you'll only need two to 3 segments.

Once you have that, you'll be able to properly position the RFG to help mitigate the protentional for drawing in air. You will also get a much better randomized flow pattern -particular if you are supplying the RFG more than 500 GPH, since that Slip-Fit Drop is going to rob you of some of the throughput.
Nevermind, I got the issue resolved.
 

TOP 10 Trending Threads

WHICH OF THESE CREEPY REEF CRITTERS IS MOST LIKELY TO GIVE YOU NIGHTMARES? (PICTURED IN THE THREAD)

  • The Bobbit Worm

    Votes: 50 66.7%
  • The Goblin Shark

    Votes: 4 5.3%
  • The Sea Wolf

    Votes: 0 0.0%
  • Giant Spider Crabs

    Votes: 1 1.3%
  • The Stargazer Fish

    Votes: 5 6.7%
  • The Giant Isopod

    Votes: 9 12.0%
  • The Giant Squid

    Votes: 1 1.3%
  • Other (Please explain!)

    Votes: 5 6.7%
Back
Top