How to wire from Lumatek ballast to MH socket?

Madison Reef

Active Member
View Badges
Joined
Dec 17, 2018
Messages
160
Reaction score
104
Rating - 0%
0   0   0
Hi,

This is my first time setting up metal halides, and I am not sure how I should connect them.
The first pic is ballast with 3 output connections, and the second pic is from bulb socket that has two wires and one ring(?).
Obviously they cannot be fitted and I am wondering if I should buy a connection cord.
Where can I find one?
20221201_183438.jpg
20221201_183451.jpg
 

oreo54

5000 Club Member
View Badges
Joined
Sep 18, 2017
Messages
5,971
Reaction score
3,674
Rating - 0%
0   0   0
I suggest starting your learning curve here..

I believe the above "parts" though not totally necessary in a sense should put it all together for you.
Adapter for your ballast to go to "standard" pin layout and a cord to go from the socket to the new adapter.

NO Guarantees but looks correct.

The pic of the wiring to the socket is incomplete.
No idea where to get a male "hydrofarm" plug.
 
Last edited:

clowndaddy420

Community Member
View Badges
Joined
Dec 26, 2021
Messages
42
Reaction score
18
Location
Bridgewater
Rating - 0%
0   0   0
green wire with the ring is a ground wire for safety and normally carries no current cut ring connector and strip wire for wire nut connection. white and black go with the positive (black) and negative (white) connections from the ballast. you may need to use a multi meter to determine this. also it may be worth while cutting the molded plug from the end of the ballast output and connecting the wires with wire nuts just for ease of connection. (this will void your warranty) further..once exposing the inner insulation the colors of the wires may already be marked under outer insulation.
 

oreo54

5000 Club Member
View Badges
Joined
Sep 18, 2017
Messages
5,971
Reaction score
3,674
Rating - 0%
0   0   0
Ok, found it.
As long as the socket cord is long enough
Wiring is self explanatory.

Hmm a catch.
Note: Minimum order quantity of 4.
 
OP
OP
M

Madison Reef

Active Member
View Badges
Joined
Dec 17, 2018
Messages
160
Reaction score
104
Rating - 0%
0   0   0
Ok, found it.
As long as the socket cord is long enough
Wiring is self explanatory.

Hmm a catch.
This looks like something I was looking for. Thank you so much for your reply.
One more question. Can I use my computer power cord to connect MH Ballast to the wall? It fits, but I am not sure if I can use it.
 

oreo54

5000 Club Member
View Badges
Joined
Sep 18, 2017
Messages
5,971
Reaction score
3,674
Rating - 0%
0   0   0
This looks like something I was looking for. Thank you so much for your reply.
One more question. Can I use my computer power cord to connect MH Ballast to the wall? It fits, but I am not sure if I can use it.
Probably not.
I just checked one of mine that had a label and it stated 18ga.
TOO thin of wire.

Check the cord for any imprinted numbers.
Look for like 16ga or 14ga painted or stamped on the cord.
Or 16/3, 4/3 ect.

Seems 16 gauge "may" be fine at lengths of 8' BUT a bit of on the edge so to speak.


Smaller the number the thicker the wire btw.

I do STRONGLY suggest thicker wires.
Only a $12-ish purchase..and if you can get one from the same place as the male plug .. hey a bonus.


Note though the spec of the 14ga..

Max Amps: 15 , Max Watts: 1800.

400w ballast at 110v is only 3.64A
Check what the ballast input states. Should be on there.
Electrical wiring specs are rather conservative for the most part.
16ga is rated for 3.7A
14ga 5.9A

EVERY calculator will show you need 14ga wire..


Hopefully a more experienced MH person will finally respond..but if not.. stick w/ 14ga.
 
OP
OP
M

Madison Reef

Active Member
View Badges
Joined
Dec 17, 2018
Messages
160
Reaction score
104
Rating - 0%
0   0   0
Probably not.
I just checked one of mine that had a label and it stated 18ga.
TOO thin of wire.

Check the cord for any imprinted numbers.
Look for like 16ga or 14ga painted or stamped on the cord.
Or 16/3, 4/3 ect.

Seems 16 gauge "may" be fine at lengths of 8' BUT a bit of on the edge so to speak.


Smaller the number the thicker the wire btw.

I do STRONGLY suggest thicker wires.
Only a $12-ish purchase..and if you can get one from the same place as the male plug .. hey a bonus.


Note though the spec of the 14ga..



400w ballast at 110v is only 3.64A
Check what the ballast input states. Should be on there.
Electrical wiring specs are rather conservative for the most part.
16ga is rated for 3.7A
14ga 5.9A

EVERY calculator will show you need 14ga wire..


Hopefully a more experienced MH person will finally respond..but if not.. stick w/ 14ga.
You suggested that I go for 14 ga for power cord, which is rated 5.9A. What about connector? It says 25ft 16/3, which is rated for only 3.7A.
I believe its the same one you suggested except its longer.
Amazon product

If I understood your explanation correctly, it is rated for only 3.7A which means I am at the limit (and risky?) if I were to run 400 watt bulb? Do I have 14 ga option for connector as well?
I am planing to run 250 watt bulb but I want to upgrade if I need to.

Thank you so much for your help.
 

oreo54

5000 Club Member
View Badges
Joined
Sep 18, 2017
Messages
5,971
Reaction score
3,674
Rating - 0%
0   0   0
You suggested that I go for 14 ga for power cord, which is rated 5.9A. What about connector? It says 25ft 16/3, which is rated for only 3.7A.
I believe its the same one you suggested except its longer.
Amazon product

If I understood your explanation correctly, it is rated for only 3.7A which means I am at the limit (and risky?) if I were to run 400 watt bulb? Do I have 14 ga option for connector as well?
I am planing to run 250 watt bulb but I want to upgrade if I need to.

Thank you so much for your help.

Well first I have to defer to " the market" as to what is standard.
Second it seems the voltage out is much higher and therefore the current much lower.
My current assumptions:
Output is DC
Output is high frequency kHz range like 20 plus kHz.

Voltage could be 400v out meaning a 400w bulb draws only 1 amp. Voltage varies for starting and current regulation as well as bulb size
Universally seems voltage in is less than voltage out thus higher current in than out.

 
Last edited:
OP
OP
M

Madison Reef

Active Member
View Badges
Joined
Dec 17, 2018
Messages
160
Reaction score
104
Rating - 0%
0   0   0
Well first I have to defer to " the market" as to what is standard.
Second it seems the voltage out is much higher and therefore the current much lower.
My current assumptions:
Output is DC
Output is high frequency kHz range like 20 plus kHz.

Voltage could be 400v out meaning a 400w bulb draws only 1 amp. Voltage varies for starting and current regulation as well as bulb size
Universally seems voltage in is less than voltage out thus higher current in than out.

Thank you for all your help!
 

TOP 10 Trending Threads

WHICH OF THESE CREEPY REEF CRITTERS IS MOST LIKELY TO GIVE YOU NIGHTMARES? (PICTURED IN THE THREAD)

  • The Bobbit Worm

    Votes: 47 66.2%
  • The Goblin Shark

    Votes: 4 5.6%
  • The Sea Wolf

    Votes: 0 0.0%
  • Giant Spider Crabs

    Votes: 1 1.4%
  • The Stargazer Fish

    Votes: 5 7.0%
  • The Giant Isopod

    Votes: 9 12.7%
  • The Giant Squid

    Votes: 1 1.4%
  • Other (Please explain!)

    Votes: 4 5.6%
Back
Top