Copper in Newly made SW

  • Thread starter Thread starter ramabama
  • Start date Start date
  • Tagged users Tagged users None

ramabama

Active Member
View Badges
Joined
Apr 5, 2017
Messages
120
Reaction score
97
Location
Jax,Fl
What state or country do you live in
Florida
Rating - 0%
0   0   0
Hello all. My display tank has been up for over a year with fish only and just added corals from a smaller tank I have. Corals are doing terrible. All parameters are in check except NO3 was very low. Got this up to around 10 (slowly over a 2 week period) and has had zero impact on corals.

So I have the Hanna High Range Copper tester I use for my QT. I thought what the heck lets test and see what we get. Test from display was .22ppm. I was like that doesnt sound good but honestly dont know. Further testing:
  • Display .22ppm
  • RODI water 0.0pp m
  • Newly made SW .17ppm
All this to ask, What is the acceptable level of Copper in DT?
 
What salt mix are you using, and what are you mixing your saltwater in?
 
Using ESV salt and mixing in a plastic container like you use for storage. Do 10 gallons at a time and immediately do water change. Mix with a pond pump I picked up on Amazon.
 
Using ESV salt and mixing in a plastic container like you use for storage. Do 10 gallons at a time and immediately do water change. Mix with a pond pump I picked up on Amazon.
Try mixing a batch by hand and then testing for copper... maybe the anazon pond pump is the source.
 
Try mixing a batch by hand and then testing for copper... maybe the anazon pond pump is the source.
Def gonna give this a shot and see. I will post back with findings.
 
Can someone confirm .22ppm in DT is unacceptable and needs to be addressed?
 
Ran out of reagent for my Hanna tester. I wont be able to do further testing until Friday.
 
Per Triton... is 3.33 ug/l also too high that I should be worried about more than usual? I'm now doing my six 15% water changes to bring it down. After 6 weeks I'll send another test to Triton. Found a 2 Little Fishies nori clip with a rusty magnet. We'll see if that was to culprit or if there are others.
 
Got more reagent and tested DT again. DT is down from .22 ppm to .12 ppm using Hanna. I have been running cuprisorb for five days.

I am going to do more testing today mixing salt to see if I can narrow down the source.
 
Mixed one gallon of SW by hand and got .01 ppm copper on the Hanna. Thats within +/- of the accuracy. Going to mix a batch with the pond pump and test.
 
From what I hear that level of copper is unacceptable.

Check the pump to see if anything touching the water is copper.

my .02
 
Mixed 10 gallons with pond pump. Hanna test was .01 ppm.

Only other thing I changed with my mixing process was I used two clean cups to measure liquid component A and B.

Before when I was getting the copper readings in newly made SW I used one cup and washed it out with tap water between measuring A&B. I guess I could have been sloppy and left some tap water in the cup. Crazy to think that would cause it but its the only other variable I can think of.
 
Per Triton... is 3.33 ug/l also too high that I should be worried about more than usual? I'm now doing my six 15% water changes to bring it down. After 6 weeks I'll send another test to Triton. Found a 2 Little Fishies nori clip with a rusty magnet. We'll see if that was to culprit or if there are others.

For an in tank value, I would not assume it is too high.
 

TOP 10 Trending Threads

HOW DO YOU HANDLE HOLIDAY DECORATING AROUND YOUR REEF?

  • I decorate the tank or stand

    Votes: 1 3.4%
  • I decorate AROUND the tank or stand

    Votes: 4 13.8%
  • I add one small seasonal touch but keep it very basic

    Votes: 0 0.0%
  • I take a holiday photo, but don’t decorate the space

    Votes: 0 0.0%
  • I leave the reef area as it is

    Votes: 20 69.0%
  • We don’t decorate for the holidays

    Votes: 4 13.8%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new