Help with my new PHOSPHORUS ULTRA LOW RANGE

Andrew Schubert

Well-Known Member
View Badges
Joined
Jul 27, 2018
Messages
646
Reaction score
320
What state or country do you live in
Illinois
Rating - 0%
0   0   0
So does anyone with experience with this testing unit have any tips on getting the regent from the little package. I think I spilled 1/4 of it try to get it out and in the vial. Seems like a horrible design as the fine powder is so hard to her out, I'm afraid that alone will screw the results.
 
So does anyone with experience with this testing unit have any tips on getting the regent from the little package. I think I spilled 1/4 of it try to get it out and in the vial. Seems like a horrible design as the fine powder is so hard to her out, I'm afraid that alone will screw the results.

Small Clear Plastic Mini Funnels for Bottle Filling, Perfumes, Essential Oils, Science Laboratory Chemicals, Arts & Crafts Supplies by (12 Pack) https://www.amazon.com/dp/B01B573D4Q/ref=cm_sw_r_cp_api_PzJ7BbY2D5WF9
 
Tap all the reagent to one side, and then cut it along the dotted line. Pull the flaps out a little bit so it makes a "slide" I guess I would call it. Then set one end into the vial and tilt it in. Then you can tap the rest in.

My first 2-3 times I was pretty frustrated with getting the powder in to, you get better at it.
 
I've heard the funnels don't work well as the powder is so fine it just sticks to the funnels....is that accurate?
 
I ran into the same problem at first. My plan of attack now is to prepare the package and fill up the test water prior to even firing up the checker. For the packet, I hold it along the sides where the cut lines are with two fingers on each side, then wiggle the reagent down into the section without the cut line. After wiggling it, I hold the packet with one hand and flick it with the other to get everything away from the cut lines. Since there are two sides with cut lines, I repeat this process for both. Once done, I cut along the cut lines. After the cut, I try to determine which of the remaining sides has most of the reagent settled against it. After making an educated guess on this, I turn the packet so this side is on the bottom, fold it there along the seam, and try to gently maneuver all remaining reagent to to the bottom.

Once the initial stage of the test is complete and it's time to add reagent, I hold the glass container on my knee (while sitting on the floor) and use my other hand to open the reagent packet into a "V", then tap it lightly against the glass rim. Since it's open in "V" shape, the opening is wider as it goes up, so that gives you a surface to hit against the glass and force everything out, while aiming it directly into the container.
 
I fold the packed diagonally and then tear or cut along the dotted line. Then open it up and you get a nice way to pour.
05D1293A-F24E-4DDE-867E-5D46B890405D.png
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.3%
  • Fish or coral food

    Votes: 5 5.4%
  • Test kits or reagents

    Votes: 10 10.8%
  • Filter media or replacement fleece

    Votes: 5 5.4%
  • RO/DI filters or supplies

    Votes: 14 15.1%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 11 11.8%
  • I keep a backup of everything

    Votes: 24 25.8%
  • Other (Post in the comments)

    Votes: 7 7.5%
Back
Top
Home
Post thread…
Market
What's new