High Magnesium, would it negatively affect SPS?

  • Thread starter Thread starter shandoee
  • Start date Start date
  • Tagged users Tagged users None

shandoee

Active Member
View Badges
Joined
Mar 8, 2020
Messages
254
Reaction score
213
What state or country do you live in
California
Rating - 0%
0   0   0
Recently I just did a 15 gallon water change on my system which is a year old, 60 gallon display with roughly 20 gallons of water in the sump. Mixed reef but mostly SPS dominated.

I have noticed that my WD and Mille have retracted polyps. All others are doing fine. The ORA pearl berry still has some PE but not as spectacular as before.
I keep my alk around 7.5, cal 500, and mg 1550 and I am using IO purple bucket. After the water change, my parameters are: dkh 7.95, Cal 5.49, Mg 1672, NO3 0, PO4 1.3
Mg levels shot up by about 120 ppm post water change.


Would very high magnesium levels have any negative effects on SPS? Mind you, my NO3 have always been reading at 0 on both hanna and nyos test kits.
 
Last edited:
I edited the original post. I looked at my numbers on my fusion app and they have been at or near the1500s, not 1300s. Doh
 
Upvote 0
I doubt it. I have never experienced nor heard of magnesium in that range causing issues.


0 nitrate and high phosphate is an issue
 
Upvote 0
I doubt it. I have never experienced nor heard of magnesium in that range causing issues.


0 nitrate and high phosphate is an issue
Yeah I’m thinking phosphate might be the issue. My nitrates have always tested 0. The WD has always shown great PE even with 0 nitrates. I may try dosing nitrates. I feed very heavily, so that is contributing to the high po4. I actually don’t like dosing anything except for dkh and ca. Thank you for responding!
 
Upvote 0
Yeah I’m thinking phosphate might be the issue. My nitrates have always tested 0. The WD has always shown great PE even with 0 nitrates. I may try dosing nitrates. I feed very heavily, so that is contributing to the high po4. I actually don’t like dosing anything except for dkh and ca. Thank you for responding!

Alternatively, you could dose amino acids. The only thing to watch for is cyano (in which you could cut down on the aminos). The coral is probably getting by via the amount of feeding you do (via fish ammonia or whatever)
 
Upvote 0
I suspect the high magnesium is test error. IO is not that high, and for a water change to boost it as much as you report would put it incredibly high in the mix.
 
Upvote 0
I suspect the high magnesium is test error. IO is not that high, and for a water change to boost it as much as you report would put it incredibly high in the mix.
Thank you for the response, Randy. I thought it was very high, especially when it went up after a water change. Initially I thought it could’ve been a bad batch so I went and bought another bucket of salt. Water change day is tomorrow so we’ll see. I have a new batch of trident reagents coming in tomorrow. I’ll test this against the salifert test kit as well.
 
Upvote 0

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.1%
  • Fish or coral food

    Votes: 5 5.3%
  • Test kits or reagents

    Votes: 10 10.6%
  • Filter media or replacement fleece

    Votes: 5 5.3%
  • RO/DI filters or supplies

    Votes: 15 16.0%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 11 11.7%
  • I keep a backup of everything

    Votes: 24 25.5%
  • Other (Post in the comments)

    Votes: 7 7.4%
Back
Top
Home
Post thread…
Market
What's new