Please advice

[pionet]

Reef-pi Som skoro hotový a uviazol som v ATO
Potrebujem dva senzory, jeden pre maximálnu hladinu a jeden pre minimálnu hladinu.
Potrebujem ovládať elektrický ventil,
môže mi niekto pomôcť s nastavením.
Mám mechanické snímače a fungujú, ale neviem to nastaviť.
Potrebujem, aby horný snímač zastavil elektromagnetické ventily a dolný snímač spustil elektromagnetický ventil a vypol sa, keď sa dosiahne horný snímač.

moja angličtina je slabá, takže prepáč.

Reef-pi I'm almost done and I'm stuck in the ATO
I need two sensors, one for the maximum level and one for the minimum level.
I need to control the electric valve,
can anyone help me with the setup.
I have mechanical sensors and they work, but I can't set it.
I need the upper sensor to stop the solenoid valves and the lower sensor to start the solenoid valve and turn off when the upper sensor is reached.

my english is weak so sorry.

 

[DC Reefer]

Are you connecting to an Apex to control your ATO?

 

[pionet]

No. Who is apex?

 

[stefanm]

Are you connecting to an Apex to control your ATO?

He mentioned it's for a reef-pi. I personally haven't set up the ATO on my reef-pi, I'll tag @Ranjib I'm sure someone who has done this will be along shortly.

Are you using something like this?

 

[stefanm]

I think I understand what you are asking, you need to wire the sensors in series.

 

[pionet]

[QUOTE = "stefanm, príspevok: 8204555, člen: 89061"]
Spomenul, že je to pre útes-pi. Ja osobne som ATO na svojom reef-pi nenastavil, označím [USER = 67835] @Ranjib [/ USER] Som si istý, že niekto, kto to urobil, bude čoskoro tam.

Používate niečo také?

[/ QUOTE]

He mentioned it's for a reef-pi. I personally haven't set up the ATO on my reef-pi, I'll tag @Ranjib I'm sure someone who has done this will be along shortly.

Are you using something like this?

yes

 

[pionet]

I think I understand what you are asking, you need to wire the sensors in series.

wire the sensors in series not working

 

[pionet]

something needs to be set via macros?

 

[stefanm]

something needs to be set via macros?

This link is from jayfish 5, not sure if it's the same as reef-pi http://www.piworx.net/wp-content/uploads/2017/04/ATO_pump_NEW.jpg

 

[stefanm]

You'll also need to add a 10k ohm resistor to ground. Post a picture of your float senior.

 

[pionet]

You'll also need to add a 10k ohm resistor to ground. Post a picture of your float senior.

I know about 10K resistance after the hardware part I have everything but I can't set Ato on the website

 

[stefanm]

I know about 10K resistance after the hardware part I have everything but I can't set Ato on the website

Take a screenshot of how you've set up the pi webpage, the connectors and the ATO configuration, pictures would help a lot, post your actual pi and connections, also the screenshots of the pi connectors (in configuration) and the ATO.

 

[pionet]

This is my electronics reef-pi

 

[pionet]

This is my pH Sonde

 

[pionet]

This is my LED electronic

 

[pionet]

This is my Rele box

 

[stefanm]

This is my electronics reef-pi

I see that you are using jumper wires, I have had many problems with those, they don't always have proper contact, on my pi I desoldered the headers and soldered the wires through the holes, definitely worth checking.

 

[pionet]

Ato seting

 

[pionet]

2

 

[pionet]

3