Reducing phosphates and dealing with hair and bubble algae

MrMeanyHead

Active Member
View Badges
Joined
Feb 17, 2026
Messages
128
Reaction score
49
Location
Pittsburgh
What state or country do you live in
Pennsylvania
Rating - 0%
0   0   0
I have a fluval evo 13.5. I currently have 2 clownfish, a linear blenny, 2 emerald crabs, and various hermit crabs and snails. I also have 2 coral so not sure if cutting light is an option.

Currently I’m trying to do water changes, feeding less, and physically removing as much algae as I can, but phosphate isn’t changing. I’m thinking of buffing up my CUC but what else should I do to reduce phosphates.

Most recent parameters were 8.0 ph, 0 nitrates, I think 1ppm phosphate(I can’t really tell with my test kit I just know it’s decently high)
 
There are many ways to reduce phosphate, but I would not assume lowering it is going to reduce algae unless you take it so low that it risks corals not getting enough.
 
Any recommendations, I’m way above where I need to be. I have trouble reading the API phosphate test kit, but it’s at least 0.75 which is way higher than it should. I just wanted some suggestions because I’ve been trying a few things and I haven’t been successful.
 
I used Phosphate RX from Blue Life. However, I would dose 1/2 of whats recommended and go slow. I never had an issue with this. If you use this make sure you have a skimmer though! If no skimmer, I would recommend GFO but use it sparingly and get yourself a better test kit. You can actually make your tank worse by zeroing phosphates.

​

 
I used Phosphate RX from Blue Life. However, I would dose 1/2 of whats recommended and go slow. I never had an issue with this. If you use this make sure you have a skimmer though! If no skimmer, I would recommend GFO but use it sparingly and get yourself a better test kit. You can actually make your tank worse by zeroing phosphates.

​

I’ll try GFO since I don’t have a skimmer and do it slowly over a few weeks
 
Any recommendations, I’m way above where I need to be. I have trouble reading the API phosphate test kit, but it’s at least 0.75 which is way higher than it should. I just wanted some suggestions because I’ve been trying a few things and I haven’t been successful.
The API phosphate tester doesn't give a number it gives a range. The first range is zero to .25, then from .25 to .5, then from point .5 to .75, etc.... My phosphate is at .03, which the API is not capable of testing, it will instead show .25.. Throw that test in garbage, its not accurate for our purposes.

The first thing to do is get a proper test kit so that you know exactly what your parameters are, then you can decide how to correct.

Can we see a picture of the tank? A fluval 13.5 AIO has a very basic filtration, IMO its not capable to handle the bioload of 3 fish, that means your main filtration should be aggressive water changes. Feeding less is not correct IMO, you added the fish to the tank so its your responsibility to feed them.
 
Last edited:
I have a fluval evo 13.5. I currently have 2 clownfish, a linear blenny, 2 emerald crabs, and various hermit crabs and snails. I also have 2 coral so not sure if cutting light is an option.

Currently I’m trying to do water changes, feeding less, and physically removing as much algae as I can, but phosphate isn’t changing. I’m thinking of buffing up my CUC but what else should I do to reduce phosphates.

Most recent parameters were 8.0 ph, 0 nitrates, I think 1ppm phosphate(I can’t really tell with my test kit I just know it’s decently high)
Zero nitrate with high phosphate does not seem likely. Consider getting LFS to run your water test.

How large of water changes are you performing?
 
The API phosphate tester doesn't give a number it gives a range. The first range is zero to .25, then from .25 to .5, then from point .5 to .75, etc.... My phosphate is at .03, which the API is not capable of testing, it will instead show .25.. Throw that test in garbage, its not accurate for our purposes.

The first thing to do is get a proper test kit so that you know exactly what your parameters are, then you can decide how to correct.

Can we see a picture of the tank? A fluval 13.5 AIO has a very basic filtration, IMO its not capable to handle the bioload of 3 fish, that means your main filtration should be aggressive water changes. Feeding less is not correct IMO, you added the fish to the tank so its your responsibility to feed them.
Which test do you recommend, I bought this one because it was on sale at a fish store going out of business.

I’m not home rn, but currently I run a 3d printed filter in chamber one, with filter floss, carbon and biomedia. The second just has my heater and light. The third has my ATO and return pump.

By feeding less, I more so meant stop over feeding. I just got the clownfish last week, my linear blenny has been in the tank for a while and is very frustrating to feed, I can’t directly feed him as he hides away if I try to, and I had to put more food in the tank because he refused to eat unless it was right in front of his face. Meaning a good amount of food would drift to the bottom.

I’m doing 15% water changes every week or every other week.
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 26 25.2%
  • I’d trust someone who knows my tank to choose

    Votes: 9 8.7%
  • I’d rather get a gift card and pick it myself

    Votes: 41 39.8%
  • I’d prefer gear or supplies instead

    Votes: 2 1.9%
  • Please don’t surprise me with livestock

    Votes: 25 24.3%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new