Safe to Buy a Used Apex Trident & DOS?

  • Thread starter Thread starter Cow
  • Start date Start date
  • Tagged users Tagged users None

Cow

Community Member
View Badges
Joined
Dec 21, 2017
Messages
76
Reaction score
24
Location
Cleveland
What state or country do you live in
Ohio
Rating - 0%
0   0   0
I’m looking at picking up a used Neptune Apex Trident and DOS combo, but the seller doesn’t have any reagents to run a test on the Trident. I’m trying to figure out whether I should order reagents and wait until I can bring them to test the unit, or if it’s reasonable to take the risk and assume it works running RODI water.

For anyone who has bought a used Trident or DOS, what was your experience like? Were there particular things you checked for before buying, such as pump heads, calibration, or leaks?

I’d love to hear some insight before I decide whether it’s worth moving forward. Thanks in advance!
 
dos are pretty easy to test, if it works it works. Trident on the other hand, even if it’s brand new and on your system might give you errors until you figure them out. So unless you have unlimited time to check, it will be a gamble either way.
 
dos are pretty easy to test, if it works it works. Trident on the other hand, even if it’s brand new and on your system might give you errors until you figure them out. So unless you have unlimited time to check, it will be a gamble either way.
Great to hear about the dos, appreciate the info. Do you know if storing it without flushing the lines properly is a machine killer or just requires some TLC?
 
Great to hear about the dos, appreciate the info. Do you know if storing it without flushing the lines properly is a machine killer or just requires some TLC?
I sell used tridents fairly frequently. The lines need to be cleared with rodi before storage, or else they will start to crystalize. Usually find that the alkalinity and waste lines are the worst. As far as checking before purchase goes, pop the cover off, look at the pinch valves to see if they are rusty (where the tubing is held right before the "spoke" looking piece), and see if the intake tubes for the reagents are "crusty" feeling. You can squeeze them and tell if it has crystallized. Overall, if the pinch valves are good, its pretty easy to service and clean out the lines. Finally, plug it into an apex or power supply and see if the pump makes any funny noises.

That's usually my checklist before sending off. The most common issue I find on used ones are "no water sample" errors, which is usually because the inline filter on the sample line is clogged. Either clean it out, or purchase a new one from neptune.
 
Great to hear about the dos, appreciate the info. Do you know if storing it without flushing the lines properly is a machine killer or just requires some TLC?
No it is not. I had mine off for over two years, without flushing the lines etc. Got it back online this month and it’s working just like it did before. My old reagents weren’t good though. You need to know how to tinker with things if you’re going to get an old trident. My machine had clogged sample line, so I had to take it apart and flush it with a 1ml syringe. You might have issues with manifold being clogged or reagents B and C being clogged. You pretty much just need to flush them. You also will likely need to take a q-tip and clean the cuvette very well. Non of those things are too difficult if you’re handy. If you aren’t getting a really good deal, or don’t want to mess with stuff like that, I’d suggest getting a brand new one. If you are a tinkerer and like to gamble, then that’s a different story. If you decide to get it at the end of the day, just throw the reagent tubes and a sample line into a cup of water, remove the dark front plate cover that hides the cuvette and run initialization as well as try priming all the lines through fusion. This will at least tell you if any of your lines are clogged, if your solenoids aren’t working properly.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new