Salinity fluctuating during cycle

Benny Morosco

Active Member
View Badges
Joined
Jul 6, 2018
Messages
148
Reaction score
149
Location
Central New York
What state or country do you live in
New York
Rating - 0%
0   0   0
is it common that the salinity goes from 35 to 37 and back down to 35 during the cycle ? Or is because I have the Apex and it is monitored that I notice it more than when I did not have it! I might be the victim of too much information!! Lol
 
Are you noting this fluctuation from the Apex probe output only, or are you using a secondary 'check' (ie refractometer) ?
 
Cycling has no detectable impact on salinity. Evaporation changing water levels does, or it is test error.
 
I am measuring with the probe on the apex and now I will measure with the refactor meter
 
That will be a good check.

You can also go into your Apex dashboard. Open up the Input Log. Select your salinity probe name to bring up the chart. Then on the right under the Compare drop down, you can select your power strip (amp).
If you are able to do this, do you see a correlation between power 'on' and an increase with your salinity probe?

I ask this, because I was unaware when I ran all my wires, and have the salinity probe running in parallel with my heater wires. My chart is a spot-on 'mimic' with the salinity increasing (probe reading) when the heaters power on.
 
Ok so this is weird I tested my water with reafactometer and it is 30 1.024 so this apex is brand new and i did all the steps to calibrate the probe can it be that much off right now my probe shows 36.8 and refact shows 30 can it be possible a 6.8 difference??
 
Unfortunately, yes it can.
Mine is off about the same as yours. I plan to mess with mine some more in the future, however, now....I don't trust it or use it. I test with a refractometer and a Milwaukee digital.

Do some looking around on this forum. You'll find a lot of stories, tips, and tricks.
 
That will be a good check.

You can also go into your Apex dashboard. Open up the Input Log. Select your salinity probe name to bring up the chart. Then on the right under the Compare drop down, you can select your power strip (amp).
If you are able to do this, do you see a correlation between power 'on' and an increase with your salinity probe?

I ask this, because I was unaware when I ran all my wires, and have the salinity probe running in parallel with my heater wires. My chart is a spot-on 'mimic' with the salinity increasing (probe reading) when the heaters power on.



here is that graph I don't see the dips...
IMG_0096.jpg
 
Unfortunately, yes it can.
Mine is off about the same as yours. I plan to mess with mine some more in the future, however, now....I don't trust it or use it. I test with a refractometer and a Milwaukee digital.

Do some looking around on this forum. You'll find a lot of stories, tips, and tricks.
Well I will only test with the refact meter going forward and I will send an email to APEX so 36.8 is 1.024 on this probe..lol
 
Well, your graph is some good news, as it doesn't appear as though you are getting very much conductivity interference.
Check around for some tips, tricks, and suggestions on getting a good (more accurate) calibration.
However, always keep a good secondary source to check your parameters.
 
Last edited:
I'm having picture issues...here's the image I was trying to show from my post above....

Salt-chart.jpg
Salt-chart.jpg


Won't fluctuations in temp effect salinity?

I believe they do, as the Apex probe is a conductivity probe, however, @Randy Holmes-Farley would be the man for a definitive answer, and lay down some science for us all! :)
 
I'm having picture issues...here's the image I was trying to show from my post above....

Salt-chart.jpg
Salt-chart.jpg




I believe they do, as the Apex probe is a conductivity probe, however, @Randy Holmes-Farley would be the man for a definitive answer, and lay down some science for us all! :)
it is right in line with your dips..
 
Actually, it's a little of both.
The green line is the power, and you can see when the power (heaters specifically) kicks on, the salinity probe reads an increase until the power cuts, then it drops back down.....like clockwork.

The lesson here, kids....don't run your conductivity probe wire parallel with your power cords. :rolleyes:
 
I thought it would be more accurate ..I submitted a ticket with Apex ..lets see what they say..
 
Yeah, won't hurt.
I know there is an advance setting for TC value, but that is beyond me at this point.

BTW, welcome to R2R, and good luck with your cycle. Mine's just finishing. Be patient, it will happen! :cool:
Also, if you don't have a build thread out there, hook us all up and show us what you have going on.
 
Ok Apex got back to me with directions on doing probe calculation manually so I did it and it still reads higher than the refact meter..
 
I just adjusted my tank water to 35 on my calibrated refractometer and then used the tank water to calibrate the Apex salinity/conductivity probe. Been pretty accurate ever since. I would never use the probe for anything important, more just a good read of short term issues like ATO malfunctions.
 

TOP 10 Trending Threads

WHAT KIND OF REEFING DEAL ARE YOU HOPING TO PICK UP THIS BLACK FRIDAY?

  • A whole new aquarium or complete system

    Votes: 4 14.8%
  • Lighting, pumps, or other major equipment

    Votes: 4 14.8%
  • Controllers, testing, dosing, or automation gear

    Votes: 2 7.4%
  • Dry goods and restocks, like salt, media, or food

    Votes: 2 7.4%
  • Corals! Must...Have...CORALS!!!

    Votes: 7 25.9%
  • Fish or other livestock

    Votes: 1 3.7%
  • Rock, sand, or other aquascaping supplies

    Votes: 1 3.7%
  • I’m browsing, but don’t have a specific target

    Votes: 4 14.8%
  • I’m not shopping for reef deals this year

    Votes: 1 3.7%
  • Other (Post in the comments)

    Votes: 1 3.7%
Back
Top
Home
Post thread…
Market
What's new