Sump/Fuge/Frag Area DIY

  • Thread starter Thread starter DudeBoy
  • Start date Start date
  • Tagged users Tagged users None

DudeBoy

Active Member
View Badges
Joined
Feb 25, 2020
Messages
108
Reaction score
152
Location
North Alabama
What state or country do you live in
Alabama
Rating - 0%
0   0   0
Wife and I are hooked and would love a second tank just for frags but I'm trying to put it off for a little while. Thought about changing out my R-200 sump with a 40g breeder with a frag area. I did see some limited info out there and even a couple pictures of what someone else did but I wanted a more general consensus......what are your thoughts? Pros, Cons, design changes?
Sump-Idea.png
 
Another question would be what type of material to use....I have access to laser cutters so perhaps acrylic (if I can find any)....
 
My opinion would be to move the skimmer before the frag section and not put sand into the frag section. Other than that I think the idea is good.
 
You should probably use glass if you can. Though I would want to use acrylic if I had access to the tools you do.
People with more experience than I say that acrylic expands over time in water and could put a lot of pressure on the outer glass. I guess if you account for that expansion, using acrylic still an option.
 
My opinion would be to move the skimmer before the frag section and not put sand into the frag section. Other than that I think the idea is good.

see any possible issues with micro bubbles messing with the skimmer if I swap it with the fuge area?

Agreed on the sand....we have sand in the display and I was just thinking that it may be beneficial to have it in the frag area too...not really sure why....lol
 
You should probably use glass if you can. Though I would want to use acrylic if I had access to the tools you do.
People with more experience than I say that acrylic expands over time in water and could put a lot of pressure on the outer glass. I guess if you account for that expansion, using acrylic still an option.

agreed...I've never done this and figure it will take a lot of tweaking. One appeal of the acrylic is that I could easily cut slots/fingers on each divider so I could fine tune it.....maybe short term is acrylic and when I get it dialed in, do glass....
 
I would swap the skimmer and frag areas and make the current frag area smaller. This would give you a larger fuge area and put the frag area in the cleanest area of the sump.
 
I would swap the skimmer and frag areas and make the current frag area smaller. This would give you a larger fuge area and put the frag area in the cleanest area of the sump.


That's a good point. One struggle is the fact that this will be inside a cabinet and I'm leery of the head room for me to get under there and maneuver around (replacing/cleaning filters, emptying sump, getting to frages, etc.). Perhaps I do flip flop the skimmer and frag area and rotate the sump 180 degrees to keep the frag visible area facing the front of the cabinet.
 
see any possible issues with micro bubbles messing with the skimmer if I swap it with the fuge area?

Agreed on the sand....we have sand in the display and I was just thinking that it may be beneficial to have it in the frag area too...not really sure why....lol

You shouldn't have a bubble issue for the skimmer. I said to remove the sand because it will just become a trap for crap and will cause issues in the future, been there done that lol
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 26 24.8%
  • I’d trust someone who knows my tank to choose

    Votes: 9 8.6%
  • I’d rather get a gift card and pick it myself

    Votes: 42 40.0%
  • I’d prefer gear or supplies instead

    Votes: 2 1.9%
  • Please don’t surprise me with livestock

    Votes: 26 24.8%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new