Apex Email Alarm Issue
- Thread starter Frederick Edwards
- Start date
- Tagged users None
Dr. Reef
www.drreefsquarantinedfish.com
First off swx3_2 is an ato sensor (seems like)
And it seems like it is in closed position most of the time till water level drops due to evaporation or water change etc then it goes to open position letting ato pump kick in to fill.
So if that's the case it will sit mostly in closed position and you have you email alert set to sent you alarm/notification for when it is closed. This will send you alert all the time as it's closed most of the time.
Under email I would reverse it to
When swx3_2 open then on
If this is your main ato sensor that detects evaporation the. I personally would not place alert/alarm on it as it will do so many times a day. If it's a secondary sensor for failsafe reason then you can have it send alerts.
And it seems like it is in closed position most of the time till water level drops due to evaporation or water change etc then it goes to open position letting ato pump kick in to fill.
So if that's the case it will sit mostly in closed position and you have you email alert set to sent you alarm/notification for when it is closed. This will send you alert all the time as it's closed most of the time.
Under email I would reverse it to
When swx3_2 open then on
If this is your main ato sensor that detects evaporation the. I personally would not place alert/alarm on it as it will do so many times a day. If it's a secondary sensor for failsafe reason then you can have it send alerts.
OP
OP
Frederick Edwards
Active Member
Sorry, I guess I should have explained what this is for?
Yes, this for auto top off system. Swx_1 is the switch that activates my top off pump and then shuts off when water level reaches Swx_1. Swx_2 is a backup sensor in case Swx_1 fails. And then if both sensors fail, there is a float valve for a third protection.
Yes, this for auto top off system. Swx_1 is the switch that activates my top off pump and then shuts off when water level reaches Swx_1. Swx_2 is a backup sensor in case Swx_1 fails. And then if both sensors fail, there is a float valve for a third protection.
Dr. Reef
www.drreefsquarantinedfish.com
This means the 3rd sensor is
3rd in line for failsafe. Which means its status is OPEN all the time till for some reason water in sump gets too high. Then it goes to CLOSE.
Your ATO setting is correct and it will turns off the pump if it ever gets that high.
But you email alert is wrong.
You need to change it to
If swx3_2 OPEN then ON
3rd in line for failsafe. Which means its status is OPEN all the time till for some reason water in sump gets too high. Then it goes to CLOSE.
Your ATO setting is correct and it will turns off the pump if it ever gets that high.
But you email alert is wrong.
You need to change it to
If swx3_2 OPEN then ON
OP
OP
Frederick Edwards
Active Member
T
Thank you, that makes sense, just wanted to be sure before I change it.
CindyKz
Valuable Member
[QUOTE="
ATO Configuration
[/QUOTE]
I'm glad to hear your alarm stopped. However, your programming still seems odd to me...
You stated there are 3 switches, but I only see two switches in your programming: "SWx3_1" and "SWx3_2". You have some redundant programming for SWx3_1 : in line 3 you tell the Apex that if the switch is open, turn on, in line 4 you tell the Apex that if the switch is closed turn off. Since the Set is off, line 4 isn't nececssary.
Did you mean for line 4 to command for the a different switch, possibly the 3rd float valve?
ATO Configuration
I'm glad to hear your alarm stopped. However, your programming still seems odd to me...
You stated there are 3 switches, but I only see two switches in your programming: "SWx3_1" and "SWx3_2". You have some redundant programming for SWx3_1 : in line 3 you tell the Apex that if the switch is open, turn on, in line 4 you tell the Apex that if the switch is closed turn off. Since the Set is off, line 4 isn't nececssary.
Did you mean for line 4 to command for the a different switch, possibly the 3rd float valve?
Dr. Reef
www.drreefsquarantinedfish.com
You don't need the closed then off statement in there. Apex will look at the open then on statement and keep pump on while if that statement turns false (closed) it will automatically turn the pump off as stated in it set off or fallback off state.
CindyKz
Valuable Member
Where's the programming for the "last resort" float valve?
Dr. Reef
www.drreefsquarantinedfish.com
That is true, currently you only have 2 switches mentioned in programming.
Swx3_1 which is you main Ato sensor
And swx3_2 failsafe
If you have 3 sensors there has to be a 3rd statement.
Similar threads
