Hiring Structural Engineer cost?

thesoulpatch

Well-Known Member
View Badges
Joined
Oct 7, 2017
Messages
624
Reaction score
335
What state or country do you live in
Wisconsin
Rating - 0%
0   0   0
Any ideas how much it would cost (or who to contact) to hire one to check out if the floor would be able to hold the weight of an aquarium? It would be in Wisconsin.

Basically moving up there and need to make sure the spot I want is able to hold it, there is a metal I-beam next to where I would like to place the tank and the beams underneath it would run parallel to the tank, along with a support holding the metal beam. I'd rather not bust a tank or ruin the floor...

TIA
 
I can't help you with the costs for hiring an engineer, but there are tables online that can tell you the weight per area that can be supported for various joist spacings and thicknesses which could get you started. When building decks for hot tubs, I've shot for 100 lb/ft2.

https://www.engineeringtoolbox.com/floor-joists-span-d_1479.html
 
it's just a 140, but with everything it's close 2000lbs. It's in a house, the tank would sit on the outside wall. I have attached the picture above where it would sit. Right above the window is where I would like it but it can be more or less centered on the I-beam if needed.

123_1 (3).jpeg
 
it's just a 140, but with everything it's close 2000lbs. It's in a house, the tank would sit on the outside wall. I have attached the picture above where it would sit. Right above the window is where I would like it but it can be more or less centered on the I-beam if needed.

123_1 (3).jpeg
As long as you are close to the load I-beam, I'd think you'd be fine. I had 180 long, on a personally-built stand (that weighed about 200+ pounds) on 10" engineered Joists for years and it was fine. It was located "nearly" above the load bearing cinder block wall in the crawl space, similarly to what you are planning.
 
As long as you are close to the load I-beam, I'd think you'd be fine. I had 180 long, on a personally-built stand (that weighed about 200+ pounds) on 10" engineered Joists for years and it was fine. It was located "nearly" above the load bearing cinder block wall in the crawl space, similarly to what you are planning.

if it's centered on that I-beam I wouldn't even worry about it.
Awesome thanks! That's a huge relief off my mind.
 
Awesome thanks! That's a huge relief off my mind.
For a 140 gallon, that's 1,200 lbs of water. Add a few hundred pounds for rock, the aquarium, stand etc., and you're not that far from 3 fat guys on a couch watching the big game!
 
Depending on your plan for the basement, you could always put in another jack post.
 
I was personally disappointed in the info I got from a very pricey structural engineer to assess a roofing situation of a very old house (not standard construction).
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.3%
  • Fish or coral food

    Votes: 5 5.4%
  • Test kits or reagents

    Votes: 10 10.8%
  • Filter media or replacement fleece

    Votes: 5 5.4%
  • RO/DI filters or supplies

    Votes: 14 15.1%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 11 11.8%
  • I keep a backup of everything

    Votes: 24 25.8%
  • Other (Post in the comments)

    Votes: 7 7.5%
Back
Top
Home
Post thread…
Market
What's new