leaking gauges

jason.tammy

Well-Known Member
View Badges
Joined
Apr 22, 2009
Messages
935
Reaction score
1
Location
Cullman
Rating - 0%
0   0   0
I need some help here.Not sure if I have to replace my guages or what.The other day all of a sudden they started leaking real bad.I shut the bottle off used teflon tape on the threads and started it back up.No leaks,came home yesterday and the bottle that I filled last week was empty agin.Is there a gasket to replace or should I replace the guages?
Jason
 
Have you sprayed some soapy water on the pressure gauge and all the fittings to determine where the actual leak is at?
 
gauges dont leak, connections leak. I have Milwaukee gauges and they have a flat nylon washer and +1 to above for soapy water
 
I'd spray soapy water anywhere you see threads. I replaced an original nylon gasket with a Teflon one due to a compression set. I have adaptors, a solenoid valve and manifolds on my CO2 injection system for my FW planted tank. I have seen gas leaks everywhere possible over the past 10 years on the setup. It's mainly because I am so feeble with renches plus all of my rube goldberg contraptions connecting different type fittings with various adaptors and tubing. A valve can leak internally, but I am going there.
 
Just an update,gauges do leak FYI.The low pressure side had blown a gasket inside the guage.All connections were good and tight with no leaks,just the GUAGE.
Jason
 
How did you find it, soapy water?
 
Just an update,gauges do leak FYI.The low pressure side had blown a gasket inside the guage.All connections were good and tight with no leaks,just the GUAGE.
Jason

opening a new cylinder without backing off the pressure setting will do that, ps lol that not a leak, its a busted
 
It was not a new bottle.It done this two weeks after the new one.Was sitting watching TV and heard it.I know opening a new bottle with the pressure up can blow seveal things.I have done it with a cutting torch before.
H@rry, took the guages to where I exchange them and hooked them up to a new bottle there and we could here it.Found it with ear and then finger.I did chk all connections and they are all good.Installed a new guage and all is well now.It is amazing how quick the paramenters can change when a reactor goes off line.
 
It is amazing how quick the paramenters can change when a reactor goes off line.

Tell me 'bout it! I have a habit of checking them several times a day. Make sure it's still bubbling and the stream is still flowing.
 
Me two now.My ALK dropped from 8 on Sunday to 5 yesterday.Seems like ounce I got the reactor back up and going things went haywire before they leveled out.
 
The dual setup of calcium reactor and kalkwasser (weakly kalk-spiked water in auto top-off reservoir) helps in this regard as well as keeping pH up. When I take my CO2 cylinder offline for a refill, I add an extra amount in kalk reservoir until I get my cylinder filled and fitted with the reactor again.
 
Yea I should have added some exstra Kalk.I still had that reactor running but the lack of calc. reactor running is pretty self telling story.I love having the reactors as long as I dont let one go down.lol
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new