Measuring PVC

burtonboy182

Active Member
View Badges
Joined
Aug 1, 2016
Messages
149
Reaction score
32
Rating - 0%
0   0   0
Wondering if anyone has any helpful hints on measuring youre plumbing. I usually get a general measurement and then start putting the pieces together and cutting it shorter if needed.
Problem I usually have is dry fitting and then glueing. When I glue it things always fit in snugger and I end up having to mark everything and put the pipes in up to my mark instead of all the way in snug. If I pushed the pipes in when I glue it all the way things wouldn’t line up.
 

Greybeard

2500 Club Member
View Badges
Joined
Feb 10, 2017
Messages
3,260
Reaction score
8,720
Location
Buffalo, MO
Rating - 0%
0   0   0
It's just practice. You learn, eventually, just how much to leave for glue joints. I would advise that you ALWAYS insert glue PVC joints as far as they'll go when you glue them up. Stopping at a mark short of full engagement is a recipe for leaks.

I'll mock up complex bits, but I no longer dry fit an entire system. Just more work.

Flex PVC or SpaFlex works pretty well in many situations where hard PVC would be more difficult to use. Once glued, it's just as permanent as hard PVC.

I keep waiting for aquarium equipment to start coming with push fit connectors for PEX. Easy, fast, can be disassembled, and doesn't leak. I'm sure it's coming, one of these days.
 

Redleg

Valuable Member
View Badges
Joined
Feb 23, 2018
Messages
1,061
Reaction score
603
Rating - 0%
0   0   0
Measure your pipe to seat completely into the hub on your fittings. Primer/ cleaner then glue it push it in the whole way and give it 1/4 turn. Then make sure to hold it in place for about 10 seconds so the pipe doesn't walk out of the fitting.
 
OP
OP
B

burtonboy182

Active Member
View Badges
Joined
Aug 1, 2016
Messages
149
Reaction score
32
Rating - 0%
0   0   0
Yes I totally agree. How much extra do you leave on both sides to account for it the part that fits into the other piece?
 

Redleg

Valuable Member
View Badges
Joined
Feb 23, 2018
Messages
1,061
Reaction score
603
Rating - 0%
0   0   0
If you measure to complete insertion depth of the hub, there is no extra to add on. You do need to consider the overall length of your fittings. There is really no set amount for those. Every pipe size and manufacturer are slightly different.
 

dbl

It Takes Less Energy to be Nice
View Badges
Joined
Mar 13, 2014
Messages
15,945
Reaction score
90,222
Location
SW Florida
Rating - 0%
0   0   0
There is a stopping point inside each fitting...typically a little ridge. Just measure that for each fitting and cut the pipe accordingly. So if you have a 12" run from point A to point B, and the stop point of each of the fittings are 3/4" inside the opening, cut the pipe 13.5" and you should be good to go.

As said above, plan accordingly and make sure you push the pipe completely in to the fitting and not some arbitrary mark. As @Greybeard said above, just takes a little practice. I like to recommend picking up a couple extra fittings (they're pretty cheap) and practice on those if you've never worked with PVC.
 

George Lopez

Well-Known Member
View Badges
Joined
May 6, 2017
Messages
531
Reaction score
285
Rating - 0%
0   0   0
If your using a pipe cutter be aware that they almost never cut straight. Also measure the in set of the fittings but they are 90% of the time the diameter of the pipe. If your making complex turns use a Sharpie to mark the parts where they fit to make sure to get the angle when you glue it and If you screw up pull it apart as fast as you can after about 20 seconds you'll need some leverage any longer than that you'll need to start over. Good luck and if you have any questions just ask.
 

George Lopez

Well-Known Member
View Badges
Joined
May 6, 2017
Messages
531
Reaction score
285
Rating - 0%
0   0   0
Oh yea, a rubber mallet is your friend or a good concrete floor to slam the fittings in against
 

Picesduh

Active Member
View Badges
Joined
Sep 14, 2017
Messages
384
Reaction score
235
Rating - 0%
0   0   0
Yes I totally agree. How much extra do you leave on both sides to account for it the part that fits into the other piece?

Search ReeferGil on YouTube and watch his plumbing video. He says how to measure it correctly.
 

Gnomy

Community Member
View Badges
Joined
May 15, 2018
Messages
25
Reaction score
10
Rating - 0%
0   0   0
Measure your pipe to seat completely into the hub on your fittings. Primer/ cleaner then glue it push it in the whole way and give it 1/4 turn. Then make sure to hold it in place for about 10 seconds so the pipe doesn't walk out of the fitting.
Don't forget to bevel the edges. ;)
 

TOP 10 Trending Threads

WHICH OF THESE CREEPY REEF CRITTERS IS MOST LIKELY TO GIVE YOU NIGHTMARES? (PICTURED IN THE THREAD)

  • The Bobbit Worm

    Votes: 50 66.7%
  • The Goblin Shark

    Votes: 4 5.3%
  • The Sea Wolf

    Votes: 0 0.0%
  • Giant Spider Crabs

    Votes: 1 1.3%
  • The Stargazer Fish

    Votes: 5 6.7%
  • The Giant Isopod

    Votes: 9 12.0%
  • The Giant Squid

    Votes: 1 1.3%
  • Other (Please explain!)

    Votes: 5 6.7%
Back
Top