Need to set bulk heads.. by climbing inside tank

Tabasco1

Valuable Member
View Badges
Joined
Dec 15, 2009
Messages
2,123
Reaction score
64
Location
Rocky Mountain High
Rating - 0%
0   0   0
This may be a silly question...

I think they only way that I can set the bulk heads in my tank is by climbing inside. This makes me nervous... but by all accounts I should weigh much less than the water/etc going inside. But I would be stepping directly onto the glass bottom in a focused area.

It is a 150g tank 50"x24"x24" There is no plastic bracing around the tank.

I'm 5'4" about 125lbs.

Should be no issue? right??
 

RobZilla04

Well-Known Member
View Badges
Joined
May 14, 2018
Messages
567
Reaction score
519
Location
St Augustine
Rating - 0%
0   0   0
No issues. If you really want to have some insurance, place a couple of 2x4's inside the tank and step/kneel on those. They will help to distribute your weight.
 

jgvergo

Valuable Member
View Badges
Joined
Nov 29, 2014
Messages
1,303
Reaction score
1,388
Location
New York
Rating - 0%
0   0   0
Hmmm, I'd vote against this move. You may weigh less than the water and rock that are going in, but you will be concentrating your weight in a very small area. The water pressure is evenly distributed over the glass.
 

jgvergo

Valuable Member
View Badges
Joined
Nov 29, 2014
Messages
1,303
Reaction score
1,388
Location
New York
Rating - 0%
0   0   0
No issues. If you really want to have some insurance, place a couple of 2x4's inside the tank and step/kneel on those. They will help to distribute your weight.
OK, something that distributes the weight will ease my discomfort a lot. Good idea.
 

jgvergo

Valuable Member
View Badges
Joined
Nov 29, 2014
Messages
1,303
Reaction score
1,388
Location
New York
Rating - 0%
0   0   0
Also, be very careful to avoid bumping or putting pressure on the walls while you are working in the tank so you don't compromise the seals.
 

Greybeard

2500 Club Member
View Badges
Joined
Feb 10, 2017
Messages
3,233
Reaction score
8,669
Location
Buffalo, MO
Rating - 0%
0   0   0
Tank fully supported underneath? No problem. You mention a rimless tank, normally, these are sitting on a firm, flat surface, right? Eh. Take off your shoes, and jump on in.

If it's only supported around the edges, then some method of better weight distribution might be called for.
 
OP
OP
Tabasco1

Tabasco1

Valuable Member
View Badges
Joined
Dec 15, 2009
Messages
2,123
Reaction score
64
Location
Rocky Mountain High
Rating - 0%
0   0   0
The tank is fully supported underneath by a a 3/4" plywood deck with a yoga mat between the tank and deck. Under the deck the stand is braced around the perimeter with 3 additional center braces.

Thanks for the speedy responses!
 
OP
OP
Tabasco1

Tabasco1

Valuable Member
View Badges
Joined
Dec 15, 2009
Messages
2,123
Reaction score
64
Location
Rocky Mountain High
Rating - 0%
0   0   0
Should I still need 2x4's in the tank? Just nervous about being able to balance on those while trying to stick my hand down the internal overflow compartment and not bump sides. :)

Or if I am able to do all that... may join the circus. :)
 

RobZilla04

Well-Known Member
View Badges
Joined
May 14, 2018
Messages
567
Reaction score
519
Location
St Augustine
Rating - 0%
0   0   0
Should I still need 2x4's in the tank? Just nervous about being able to balance on those while trying to stick my hand down the internal overflow compartment and not bump sides. :)

Or if I am able to do all that... may join the circus. :)

For peace of mind you can use 2x4's.
 

Creating a strong bulwark: Did you consider floor support for your reef tank?

  • I put a major focus on floor support.

    Votes: 57 39.6%
  • I put minimal focus on floor support.

    Votes: 33 22.9%
  • I put no focus on floor support.

    Votes: 49 34.0%
  • Other.

    Votes: 5 3.5%
Back
Top