Off-centered tank on stand?

[Mikedawg]

Misunderstood. I have not used coins nor any other materials to shim the tank or stand.

Thanks for clarifying; thought I saw some under left side of tank which seemed to have a small gap between it and stand. Would still go with adding plywood as an inexpensive fix.

 

[JoshH]

The screws/square piece holds the two top panels together.

I think this would be the real reason for adding a top piece.

 

[aquatony]

Plywood is pretty much garbage if it continuously gets wet... I’d go with 2x4. Where ever you can fit and if it’s in sight throw some black paint on it. Cut them to length. Screw them to existing stand from the outside. Good to go..

 

[redfishbluefish]

What type of plywood should I get?

Also will I need to glue/screw the new top onto the old top?

I've made four stands over the past 4 - 5 weeks and really like THIS plywood from HD....I think I've purchased five sheets. It was selling for 31.98 per 4x8 sheet, but about two weeks ago it went up to 34.98. Both sides look pretty good, but the one side is nicely finished. It will take paint/stain/polyurethane very nicely....PROTECTING the plywood from occasional water.

 

[zcedric]

It is a rimless tank. I would add some styrofoam under it. To equal pressures out.
Its only a 30g so i think it will hold it. Maybe add some braces right under the tank to support.
What scares me are these metals with 4 screw which hold the plates together.... lows has some good 4 x 4 wood mounting brackets which look similar.. maybe you want to add 2 more.

 

[mrpizzaface]

I’m definitely not an engineer, with that being said, I think you will be fine.

 

[cmcoker]

Thanks for clarifying; thought I saw some under left side of tank which seemed to have a small gap between it and stand. Would still go with adding plywood as an inexpensive fix.

I thought so too what's the white stuff and is there a gap under that left corner?

 

[samnaz]

I thought so too what's the white stuff and is there a gap under that left corner?

There isn't a gap between the tank and stand, there is a foam leveling mat.

The white stuff is just leftover foam protection that I wrapped the tank in when I had to lay it face down to drill holes on the back glass.

 

[samnaz]

I've made four stands over the past 4 - 5 weeks and really like THIS plywood from HD....I think I've purchased five sheets. It was selling for 31.98 per 4x8 sheet, but about two weeks ago it went up to 34.98. Both sides look pretty good, but the one side is nicely finished. It will take paint/stain/polyurethane very nicely....PROTECTING the plywood from occasional water.

That's still plenty cheap enough. Thing is, I don't have a saw to cut it to size so I was looking at this...
https://www.homedepot.com/p/Columbi...=REC-_-rv_cart_rr-_-204853877-_-203553007-_-N

Would that work or no?

 

[LobsterOfJustice]

They will cut it to size for you there if you ask.

 

[JoshH]

That's still plenty cheap enough. Thing is, I don't have a saw to cut it to size so I was looking at this...
https://www.homedepot.com/p/Columbi...=REC-_-rv_cart_rr-_-204853877-_-203553007-_-N

Would that work or no?

That will work great as Well, just a different (more expensive) type of wood/finish and the smaller sizes are usually more expensive as well. As lobster said, they will cut your sheet to whichever size you want give or take 1/8" for free.

 

[samnaz]

Great thanks for the help everyone.

 

[mjlash22]

What type of plywood should I get?

Also will I need to glue/screw the new top onto the old top?

Most hardware stores will sell particle board or for a little more, nicer plywood. I would go with the nicer stuff.

 

[samnaz]

I went with Baltic Birch.