phosphates 1.0 nitrates 5ppm

  • Thread starter Thread starter teff738
  • Start date Start date
  • Tagged users Tagged users None

teff738

New Member
View Badges
Joined
Jun 15, 2021
Messages
8
Reaction score
2
Location
Nova Scotia
What state or country do you live in
Canada
Rating - 0%
0   0   0
so as stated my phosphates are sitting at 1 and my nitrates are at 5ppm, ammonia and nitrites are both 0, salinity is 33.6, temp 78, mag is 1390,Calcium is 400-500, alk is 9.4, and ph is 7.8.. just got 2 brand new trachy and am seeing some minor recession...can anyone guess what's happening here I'm at a loss, feeding is redhead ab+ with music and reefroids twice a week on different days, dosing nopox, tank is a 90gal lps/softies with an eshopps r3 sump refugium with macro algae...
 
Phosphates are high. Nitrates are fine. I would run some GFO
 
Po4 at 1ppm, use lanthanum chloride, diluted, dripped over 8 hours.
Stop the reefroids, they are mostly phosphate.
 
was thinking chemipure..thoughts?
Chemipure elite contains gfo.
Gfo is used for maintaining low, < 0.2 ppm po4.
At 1ppm alot is bound to rock and substrate. It will take a lot of gfo to remove 1 ppm po4.
Lanthanum chloride is the best remover in this case.
Once po4 below 0.2 ppm, run gfo in a reactor.
 
Chemipure elite contains gfo.
Gfo is used for maintaining low, < 0.2 ppm po4.
At 1ppm alot is bound to rock and substrate. It will take a lot of gfo to remove 1 ppm po4.
Lanthanum chloride is the best remover in this case.
Once po4 below 0.2 ppm, run gfo in a reactor.
the lanthanum scares me honestly,would rather not boink all my fish...
 
the lanthanum scares me honestly,would rather not boink all my fish...
The risk is the lanthanum phosphate flocculant, which is 5 to 10 microns particulate size. Certain tangs are at risk due to particles clogging their gills. The story goes: after dosing lanthanum, my fish swam into the cloud didn't make it out the other side. This indicates using the product incorrectly, as there should be no cloud unless you are doing it wrong.
I use brightwell aquatics phosphate e, diluted 50:1, dripped into the overflow over 8 hours. The lanthanum reacts with the phosphate on contact, so i trap the overflow water with a 5 micron sock. Also run a skimmer.
There is no cloud, or any perceived cloudiness.
Others do not go to these measures, but it is easy for me to do every 3 months or so, when the po4 rises above 0.4ppm.
Lanthanum removes phosphate, that is all it does.
Gfo removes phosphate and some other things. If may leach iron into water, which may be good or bad. In your case gfo should be run in a reactor.
 
the lanthanum scares me honestly,would rather not boink all my fish...
It is good to be cautious. Understand the risks then make your decision. Use the search feature to learn about lc.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 17.7%
  • Fish or coral food

    Votes: 5 5.2%
  • Test kits or reagents

    Votes: 10 10.4%
  • Filter media or replacement fleece

    Votes: 5 5.2%
  • RO/DI filters or supplies

    Votes: 15 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 12 12.5%
  • I keep a backup of everything

    Votes: 25 26.0%
  • Other (Post in the comments)

    Votes: 7 7.3%
Back
Top
Home
Post thread…
Market
What's new