Phosphates waaay to low, need advice

  • Thread starter Thread starter bct15
  • Start date Start date
  • Tagged users Tagged users None
I'M SORRY, this statement is plane and simple false. Coral do need a certain amount of po4 (.03-.05) and nitrates to do well and maintain color as others have mentioned. FEED your tank.:wave:

Don't need phosphates, how is your Nitrates? Bet they are to low for your LPS. Your phosphates are right where they should be.
 
I'M SORRY, this statement is plane and simple false. Coral do need a certain amount of po4 (.03-.05) and nitrates to do well and maintain color as others have mentioned. FEED your tank.:wave:
If you say so. Got a guy above me says his are 0 also and doesn't have any problems. But, what the heck do i know.
 
Not sure I have any.... I just know what works for me.;)

Sent Via the R2R Forum APP
 
Last edited:
I''ve heard some people say they have success with phosphate and others who say the have success without. So obviously good results can be achieved both way. I think the people with zero phosphates probably have to feed their corals as do i. Maybe I should raise phosphates so I don't have to bother feeding them. :)
Sent Via the R2R Forum APP
 
Some of my larger sps colonies are showing burnt tips, and a couple frags a little recession around the base. I had a chalice frag slowly recede to death, and a couple blastos are staying deflated. Some macro algae in my fuge is turning clear, and I haven't had to wipe my glass in about two and half weeks. I also had two small Zoa colonies stop opening and melt in the last month and a half. Also, my pizza anemone hasn't been able to find a place to stay put for about two months now. Even the back glass and side that I don't wipe (for my snails and tangs to graze) is clearing up. I was excited about no algae at all, but now I think it is clean to a point that it is causing problems.

I'm having the same problem with my garf bonsai acro and one othe frag.




Sent Via the R2R Forum APP
 
The phosphate issue really depends on how u remove it. Agressive filtration like biopellets and gfo strip it to fast so the corals dont get what they need. Less aggressive methods like algae can run a tank at 0.00 and do fine. If u dont believe me come look at my corals or the ocean. I use an algae scrubber and run at 0.00 hanna checker and sps has great color. Also have a good number of fish and feed fairly heavy. And i do not feed corals.
 
I'm running a full Zeovit system so I'm already low on nutrients.


Sent Via the R2R Forum APP
 
Last edited:
I'M SORRY, this statement is plane and simple false. Coral do need a certain amount of po4 (.03-.05) and nitrates to do well and maintain color as others have mentioned. FEED your tank.:wave:

Corals do need certain amount of phosphate but nowhere near (.03-.05) like you mentioned.

Another important not us the Hanna checker only has an accuracy of +/- 0.04 I believe. That means a 0.00 reading could actually be 0.04. Don't go crazy over a 0.0 reading on a cheap Hanna checker.
 
Corals do need certain amount of phosphate but nowhere near (.03-.05) like you mentioned.

Another important not us the Hanna checker only has an accuracy of +/- 0.04 I believe. That means a 0.00 reading could actually be 0.04. Don't go crazy over a 0.0 reading on a cheap Hanna checker.

What is a good/accurate way to measure phosphate.




Sent Via the R2R Forum APP
 
The Hanna is probably the best affordable way to check it. To get more accurate you are going to spend some serious money on more sophisticated equipment.

+/- 0.04 is pretty good. Certainly better than test kits.
 
FYI

The +/- .04 error is not a constant value, it is a value you plug into a formula to get your true error based off of the measurement reading. A reading of zero is a reading of zero based on the zero level calibration point and the true error will come back as zero + calibration error. That number they give comes from the point of maximum error on a data set containing the measurement range if the equipment.

I am 95% sure on what I said, I haven't done an error analysis in a while though and may be a little bit wrong, I can go digging through my books if further verification is required.


Sent Via the R2R Forum APP
 
Last edited:
In think the accuracy means that the instrument can potentially be +\- 0.04 the actual value at any given point within the instrument range.

For example, when we perform a 3 point calibration on an instrument at work. We have a specified accuracy. If our specified accuracy is let's say 0.04 and the as found value is within +\- 0.04 of the standard at the low, middle, and high points it is considered to be within calibration and no adjustments are necessary.
 
Last edited:
You both are wrong.

The set points maximum calibration is equal to the variation of such standard solutions used to mediate the reaction. It is often theorized that the lowest common denominator is only +/- .04, but that doesn't take into consideration the tectonic plates or earths exact position in space. The variance in degrees of longitude directly relate to the phosphate levels in the tank, making precision very difficult, unless the calibration was done at the same geographical location. Obviously I know I'm right on all of this...obviously ;-)


Sent Via the R2R Forum APP
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 26 23.4%
  • I’d trust someone who knows my tank to choose

    Votes: 10 9.0%
  • I’d rather get a gift card and pick it myself

    Votes: 45 40.5%
  • I’d prefer gear or supplies instead

    Votes: 2 1.8%
  • Please don’t surprise me with livestock

    Votes: 28 25.2%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new