Post Your TDS and Location

[Waynerock]

Fletcher NC right outside Asheville NC and I am getting 22 TDS right outta the tap

 

[DanATL]

I get 62 TDS out of my whole house Aquasana Rhino filter. That goes to my RODI. I get 1TDS after RO membrane going into DI canister with a consistent 0 TDS final product. This is Cobb County, Georgia (suburban Atlanta). I have no idea of the county source water TDS.

 

[AstroMelly]

280 TDS well water near Gainesville, FL
12 after RO
0 after DI until I exhausted the resin! That happened very quickly, probably due CO2 in well water.

Maybe look at sourcing a better RO filter - 12 ppm from your RO membrane is high and will deplete your DI resin quickly (as you noted). For me 5-6 is ok - I used to get 300-400 litres before the DI resin was depleted. I just bought a premium RO filter and now I am getting 3ppm (sometimes 2) output from the RO membrane. My DI resin should last maybe twice as long now (before the membrane change it was up to 7 but normally ran at 5-6). IMO a few pounds on an improved membrane filter that should last 6-9 months is worth it since changing the DI resin is a pita! For reference our tap is at 280-300, similar to yours.

 

[bushdoc]

Maybe look at sourcing a better RO filter - 12 ppm from your RO membrane is high and will deplete your DI resin quickly (as you noted). For me 5-6 is ok - I used to get 300-400 litres before the DI resin was depleted. I just bought a premium RO filter and now I am getting 3ppm (sometimes 2) output from the RO membrane. My DI resin should last maybe twice as long now (before the membrane change it was up to 7 but normally ran at 5-6). IMO a few pounds on an improved membrane filter that should last 6-9 months is worth it since changing the DI resin is a pita! For reference our tap is at 280-300, similar to yours.

Not really, his rejection rate is 95.7%, which is average. It is his water initial TDS so high which is problematic. For human consumption purposes you could go below 90% rejection rate, for reefing most likes it 92-95%.

 

[T-J]

Maybe look at sourcing a better RO filter - 12 ppm from your RO membrane is high and will deplete your DI resin quickly (as you noted). For me 5-6 is ok - I used to get 300-400 litres before the DI resin was depleted. I just bought a premium RO filter and now I am getting 3ppm (sometimes 2) output from the RO membrane. My DI resin should last maybe twice as long now (before the membrane change it was up to 7 but normally ran at 5-6). IMO a few pounds on an improved membrane filter that should last 6-9 months is worth it since changing the DI resin is a pita! For reference our tap is at 280-300, similar to yours.

Mine is also about 12 after the RO (source water is mid 500s). My DI resin lasts a crazy long time.

 

[wdotero]

Maybe look at sourcing a better RO filter - 12 ppm from your RO membrane is high and will deplete your DI resin quickly (as you noted). For me 5-6 is ok - I used to get 300-400 litres before the DI resin was depleted. I just bought a premium RO filter and now I am getting 3ppm (sometimes 2) output from the RO membrane. My DI resin should last maybe twice as long now (before the membrane change it was up to 7 but normally ran at 5-6). IMO a few pounds on an improved membrane filter that should last 6-9 months is worth it since changing the DI resin is a pita! For reference our tap is at 280-300, similar to yours.

Thanks for the feedback! For now my options are limited because I am using the RODI buddie system. In the future, I will definitely go with a better system that uses standard size cartridges.

 

[Tangdora]

South Jersey, Well water.

103-at tap
6 - after membrane
0 - after Di

Curious if there is suppose to be any reduction alone from the pre filter befor membrane, only getting a 1 point drop after passing through a 5 micron filter, gac and cto filter. Wondering if this ispring brand off Amazon is robbing me. Perhaps should switch to 1 micron ?

 

[scottberto]

Coastal Georgia- 3-7 out of the backyard hose lol
0 after BRS 7 stage (overkill, I know)

 

[Gtinnel]

South Jersey, Well water.

103-at tap
6 - after membrane
0 - after Di

Curious if there is suppose to be any reduction alone from the pre filter befor membrane, only getting a 1 point drop after passing through a 5 micron filter, gac and cto filter. Wondering if this ispring brand off Amazon is robbing me. Perhaps should switch to 1 micron ?

The sediment and carbon pre filters will not make any significant difference to the tds of the water before it goes through the membrane.

 

[john_ob]

Franklin in Western NC.
9 from the tap.

 

[X-37B]

Sacramento county 46 tds from the tap.