Sauced and Confused (Lost Remix)

my guess is I will do the stand this weekend and see how I feel after about doing another DIY, woodworking is one thing have all the tools and do it daily anyway --- sump being all glass sounds less fun :p
Could go with plexi? I never built a tank or a sump. I seen a lot of sumps made from plexi. Do we even call it plexi still?

or is it acrylic?
 
I don't know any of it.

But, it's an option vs glass cutting.
Building a sump using an existing sized, readily available tank, You don't need to cut any glass.

Take your measurements off the tank, cut the acrylic - 1/4"

Route in water passage/weirs if desired, and silicone in place.
 
Could go with plexi? I never built a tank or a sump. I seen a lot of sumps made from plexi. Do we even call it plexi still?

or is it acrylic?
I believe they call it acrylic now
 
Building a sump using an existing sized, readily available tank, You don't need to cut any glass.

Take your measurements off the tank, cut the acrylic - 1/4"

Route in water passage/weirs if desired, and silicone in place.
I'm not cutting anything, unless it's a steak!
Meat Steak GIF by Beef. It's What's For Dinner.
 
Building a sump using an existing sized, readily available tank, You don't need to cut any glass.

Take your measurements off the tank, cut the acrylic - 1/4"

Route in water passage/weirs if desired, and silicone in place.
I think my only other concern with DIY on this is if I mess up the flow but I guess that would be kinda hard anyway since its just compartments. Do you find that overflow is enough or buy acrylic that has flows in the middle of it is important?
 
Visual reference. The baffles took less than 2 hours from unboxing, To ready for install.
PXL_20221102_192650422.jpg
PXL_20221102_221929108.jpg
PXL_20221103_002536295.jpg
PXL_20221103_005605685.jpg
PXL_20221103_221252392.jpg
PXL_20230419_181533016.jpg
ok you answered my above with th is, you ordered them offline already pre made... this makes a lot more sense

love the hardplumbing too tbh always found it better
 
ok you answered my above with th is, you ordered them offline already pre made... this makes a lot more sense
I did not order any of those baffles pre-made. @F i s h y was kind enough to cut them oversized from his acrylic hord and send them to me.

I used to half inch up spiral router bit to cut central flow. 1/4" spiral bit on the router table to cut the weir teeth on an adjustable baffle (pictures above) so that I can change the running water height in some.
 
My wifes one request is that my sump can't sit on the hardwood, so I believe when I make the stand this weekend I will just support the bottom as well as the top and skin it with ply so it can support the sump weight also
 
I am leaning towards a 40g sump on the 120, so the size probably would be noticeably smaller than yours maybe, I guess I could however go bigger if I wanted and was DIY'ing it
Where are you located?

I run a 40 breeder sump with Fiji cube inserts under my 120. It's a great size. Doesn't leave a whole lot of room under the stand, but enough.
PXL_20230419_183404349.jpg
 
Where are you located?

I run a 40 breeder sump with Fiji cube inserts under my 120. It's a great size. Doesn't leave a whole lot of room under the stand, but enough.
I am in Pittsburgh, PA, yeah thats what I was thinking about the 40 breeders are pretty readily available also
 
I am lucky that the laundry room (with easy access to water is right behind the wall of where I am placing this too) I already started to go through the drywall and cement behind and running the lines for the rodi and maybe one day ATO
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new