Tunze osmolater 3 nano (new) overfilling

offthehook

Active Member
View Badges
Joined
Sep 26, 2010
Messages
305
Reaction score
158
Location
Eastern NC
Rating - 0%
0   0   0
Brand new (less than a week old). Seems to be doing ok but from time to time it seems to overfill just over the top of the sensor housing, (see picture). Sorry best I could do in the dark. Trying to figure out why this may be happening, I narrowed it down to maybe the water coming in from the ATO is splashing causing disturbance around the sensor cover but not 100% on that. It’s a small area so I don’t have a lot of places to put the ATO incoming water, tomorrow, I will try to shorten it so it hits the wall first before hitting the water in the chamber but still wanted to check in here to see if there could be other issues. Not a snail as I have a lid and no snails are in the back chambers . It’s in with my return pump so no real water turbulence. Any other thoughts.

Also I understand there are two filling time limits, one is 77 seconds ( 0.4 gallons) and the other is like 154 seconds (0.8 gallons I think). I assume it is default from factory set at the lower time limit? If it hits that limit it cuts off and has to be unplugged and plugged in again to work …is this correct. If so this does make me fill slightly better.

IMG_1980.jpeg
 
Your understanding of the safety is correct. The main causes of this kind of behavior is UV sterlizers or growlights. Growlights emit infared which is what the sensor uses to detect water level. Flourescent lights have ballasts and these ballasts create a strong EMF, how much depends on the quality of the ballast, this "noise" can cause disruption to the processor. Assuming the ballast/light is of reasonable quality a distance between them and understanding that all wiring acts as antennas to conduct and transmit this interference so the wires must be separated will usually solve it. I have seen physical causes as well, splash can be a cause but has to be extreme and more common is momentary disruptions of flow, a fish, snail etc blocks the overflow and the water level drops and then comes back up when it moves and the resultant overflow is caused by this momentary low water level.
 
Your understanding of the safety is correct. The main causes of this kind of behavior is UV sterlizers or growlights. Growlights emit infared which is what the sensor uses to detect water level. Flourescent lights have ballasts and these ballasts create a strong EMF, how much depends on the quality of the ballast, this "noise" can cause disruption to the processor. Assuming the ballast/light is of reasonable quality a distance between them and understanding that all wiring acts as antennas to conduct and transmit this interference so the wires must be separated will usually solve it. I have seen physical causes as well, splash can be a cause but has to be extreme and more common is momentary disruptions of flow, a fish, snail etc blocks the overflow and the water level drops and then comes back up when it moves and the resultant overflow is caused by this momentary low water level.
Thanks, with the small chambers in the back housing all the electrical items, the wires are bound to be close, hopefully I have them separated enough to not cause issue. Haven’t had a chance to check it today to see if it has done it again. But hopefully not, I’ll keep an eye out for sure. I don’t have a red grow light but do have a uv in the next chamber but is fully enclosed so the light does not shine through. I use led lighting and have a shade on it so not a ton of overspill into the chambers.
 
With UV it has nothing to do with light, it is the fact that modern electronic flourescent ballasts create an electromagnetic field that disrupts the functions of the processor in the controller, you can generally detect this interference on a radio or TV as static. Wiring serves as antennas transmitting and receiving this interference signal. We saw this same issue in the past when PC lights were popular and the situation is similar, if the bulbs are old, the problem gets worse, if the ballast is exceptionally low quality, it may not even be possible to share the same household circuit, on the other hand higher quality ballasts need minimal isolation, in the case of PC lights the cheapest DIY kits were highly problematic, the best made fixtures were relatively issue free. From what we have seen, best practice is maximum distance between the products, wires of one on one side of the set up, wires of the other on the other side, UV on a separate surge supressor strip (the circuitry helps filter the noise) and the Osmolator on another. A practical way to do this is UV, lights, on one strip, filter, ATO components on another.
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 26 24.1%
  • I’d trust someone who knows my tank to choose

    Votes: 9 8.3%
  • I’d rather get a gift card and pick it myself

    Votes: 44 40.7%
  • I’d prefer gear or supplies instead

    Votes: 2 1.9%
  • Please don’t surprise me with livestock

    Votes: 27 25.0%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new