1/4" Bulkheads that work for dosing?

nothing_fancy

Active Member
View Badges
Joined
Oct 6, 2022
Messages
435
Reaction score
367
Location
usa
What state or country do you live in
New Jersey
Rating - 0%
0   0   0
Hi, I'm looking to see if anyone has any recommendations for good 1/4" bulkheads that I can use on the caps of my KZ bottles. The Murdock bulkheads that they sell on BRS have pretty bad reviews which I found surprising since most Murdock products IME have been good for me. I'm already using (4) dosing containers in my stand and Im out of room so Id like to simply drill holes in a few of my elements bottles and auto dose them out. Most of the reviews for the murdock brand bulkheads say they lose prime. Hoping someone can give some clarity on a product they have seen to be reliable for this application. Thanks!
 
Hi, I'm looking to see if anyone has any recommendations for good 1/4" bulkheads that I can use on the caps of my KZ bottles. The Murdock bulkheads that they sell on BRS have pretty bad reviews which I found surprising since most Murdock products IME have been good for me. I'm already using (4) dosing containers in my stand and Im out of room so Id like to simply drill holes in a few of my elements bottles and auto dose them out. Most of the reviews for the murdock brand bulkheads say they lose prime. Hoping someone can give some clarity on a product they have seen to be reliable for this application. Thanks!
Mur-loks are just fine. The main reason people have many issues with them usually equates to bad cut tubing (inward belled that doesnt make 360 contact with the O-ring) Or a dry O-ring that causes the tubing to be not fully seated past the o-rings seal.

I think john guest uses a metal affixing ring but its similar quality.
 
Mur-loks are just fine. The main reason people have many issues with them usually equates to bad cut tubing (inward belled that doesnt make 360 contact with the O-ring) Or a dry O-ring that causes the tubing to be not fully seated past the o-rings seal.

I think john guest uses a metal affixing ring but its similar quality.
Thanks, so you're saying this is mostly user error and that a straight cut of ro or rigid tubing is the way to go?
 
Thanks, so you're saying this is mostly user error and that a straight cut of ro or rigid tubing is the way to go?
Yes. I use a pvc tubing cutter (a little big and overkill) but, it works to make a nice straight, cut without crushing the end of the tubing like sidecutters or scissors would.
You can alternatively use a razorblade on a flat surface.
 
Yes. I use a pvc tubing cutter (a little big and overkill) but, it works to make a nice straight, cut without crushing the end of the tubing like sidecutters or scissors would.
You can alternatively use a razorblade on a flat surface.
Awesome, thank you, I have something similar to that for straight cuts. Appreciate it.
 
I just used different colors of Silicone Airline tubing, put that over Lee’s Rigid Tubing. Drilled a hole in an empty Simply Lemonade Bottle Cap, forced the Rigid through the hole, drilled a tiny breather hole next to the tubing hole. Adjusted the Lee’s tubing so it was just off of the bottom.
 
I have used the BRS ones with good success. . . they don't come with a gasket. . . I have had good luck using garden hose gaskets or just random ones from the home depot plumbing isle that are approximately the right size.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 17.7%
  • Fish or coral food

    Votes: 5 5.2%
  • Test kits or reagents

    Votes: 10 10.4%
  • Filter media or replacement fleece

    Votes: 5 5.2%
  • RO/DI filters or supplies

    Votes: 15 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 12 12.5%
  • I keep a backup of everything

    Votes: 25 26.0%
  • Other (Post in the comments)

    Votes: 7 7.3%
Back
Top
Home
Post thread…
Market
What's new