125 - Took Forever But Here It is!

[tbrown]

yeah, I texted to see what it meant. turns out "clothes that look half decent and won't be too hot for a New York summer".

So Crocs with socks

 

[Mschmidt]

So Crocs with socks

I think I suggested sockless boat shoes, so seven-figure salary crocs.

 

[Abyzter]

Setup:
Tank
125 Gallon (72"*19"*24") glass tank
Sump
Eshopps RS200 3rd Gen
Bubble Magus Curve 7 IOAOI Reef 120
Green Machine 9 watt UV Sterilizer (as
needed)
Jebao DP-4 Dosing pump
Lights
Noopsyche K7 V3 140 watt x 2
Noopsyche K7 Pro II 90 watt Noopsyche K7 Pro III 140 watt
Noopsyche K7 V3 75 watt
Stand
Homemade steel square stock (way
overkill)
Heater
300 watt Inkbird Titanium Heater
250 watt Rena Inline heater
Inkbird Heater Controller
Sand
40 lbs Arag Alive Pink Fiji sand to start
with an additional 40 lbs in the 75
and 10 more in the 5 gallon
Rock
Approximately 25 pounds now plus
an additional 50 lbs in the 75 and
10 more in the 5 gallon

Progress Pictures:

Some "Key" Posts:

Disaster Strikes!
https://www.reef2reef.com/threads/125-took-forever-but-here-it-comes.907906/post-10290830
Painted and Getting Ready
https://www.reef2reef.com/threads/125-took-forever-but-here-it-comes.907906/post-10357759
Tank is Inside
https://www.reef2reef.com/threads/125-took-forever-but-here-it-comes.907906/post-10360160
Plumbing, Rockwork,and Sand Added
https://www.reef2reef.com/threads/125-took-forever-but-here-it-comes.907906/post-10364020
Aragocrete frag rack project walk-through
https://www.reef2reef.com/threads/125-took-forever-but-here-it-comes.907906/post-11213452

DISCLAIMER: THIS 125 TANK IS STILL RUNNING. HOWEVER, I won an ESHOPPS Mariner 70 so I'm going to have a build for that and don't want to lose this one. This is still my main build thread until I decide it's not?

https://www.reef2reef.com/threads/eshopps-mariner-70-build.1020962/

I'm excited to see how your tank turns out!

 

[tbrown]

I'm excited to see how your tank turns out!

It's about to un-turn out. I'm in the middle of a tank transfer.

 

[JoJosReef]

Why?

It's saying "just the tip".

 

[Fish Styx]

 

[907_Reefer]

Me catching up on the last 5 pages:

 

[stoney7713]

Well I'm down.

Extruder quit this morning, I done everything I could. Contacted creality support, 20 minute wait on replies, I finally got a support ticket, they said to give them at least 5 days and if I don't hear anything to reach out again.

 

[Mschmidt]

Well I'm down.

Extruder quit this morning, I done everything I could. Contacted creality support, 20 minute wait on replies, I finally got a support ticket, they said to give them at least 5 days and if I don't hear anything to reach out again.

Sorry about that. Is also frustrating costumer service.

 

[tbrown]

Did you check the wires to make sure nothing came unsoldered?

 

[stoney7713]

Sorry about that. Is also frustrating costumer service.

I've heard the stories. I just hope they agree just to send me a new extruder.

Bambu keeps showing the P1S and AMS as presale. I guess I'll place my order and wait.

 

[stoney7713]

Did you check the wires to make sure nothing came unsoldered?

Yup disassembled and checked everything.

 

[stoney7713]

Did you check the wires to make sure nothing came unsoldered?

Also had the main board cooling fan go out about 6 months ago, I just replaced it myself. That was quick, easy and cheap.

 

[Mschmidt]

I've heard the stories. I just hope they agree just to send me a new extruder.

That'd be the easy solution.

Bambu keeps showing the P1S and AMS as presale. I guess I'll place my order and wait.

Hope not too long.

 

[stoney7713]

That'd be the easy solution.

Hope not too long.

I've read a few cases where they simply supplied the broken part.

But there are sooooo many more, lack of resolution.

I did buy an extended warranty because of all the bad stories of warranty, so if there's no fix from creality I can use it

 

[stoney7713]

Less than 2700 hours on the printer. 12,442 meter of filament used, 7.73 miles, or 69,122 bananas.

 

[stoney7713]

Took awhile but I got it covered

 

[Mschmidt]

Less than 2700 hours on the printer.

That's a part time job.

12,442 meter of filament used,

What's a meter?

7.73 miles, or 69,122 bananas.

 

[Mschmidt]

Took awhile but I got it covered

Pretty please could you share the stl?

 

[stoney7713]

Pretty please could you share the stl?

Yeah let me get it zipped up. @tbrown maybe you should try it too, it's a quick and easy manual filament change, just set it in your slicer.