OP
OP
tbrown
Nominated Cronie Intern - Might be failing?
So Crocs with socks
125 - Took Forever But Here It is!
- Build Thread
- Thread starter tbrown
- Start date
- Tagged users None
I think I suggested sockless boat shoes, so seven-figure salary crocs.
I'm excited to see how your tank turns out!Setup:
Tank
125 Gallon (72"*19"*24") glass tank
Sump
Eshopps RS200 3rd Gen
Bubble Magus Curve 7IOAOI Reef 120
Green Machine 9 watt UV Sterilizer (as
needed)
Jebao DP-4 Dosing pump
Lights
Noopsyche K7 V3 140 watt x 2
Noopsyche K7 Pro II 90 wattNoopsyche K7 Pro III 140 watt
Noopsyche K7 V3 75 watt
Stand
Homemade steel square stock (way
overkill)
Heater
300 watt Inkbird Titanium Heater
250 watt Rena Inline heater
Inkbird Heater Controller
Sand
40 lbs Arag Alive Pink Fiji sand to start
with an additional 40 lbs in the 75
and 10 more in the 5 gallon
Rock
Approximately 25 pounds now plus
an additional 50 lbs in the 75 and
10 more in the 5 gallon
Progress Pictures:
Some "Key" Posts:
Disaster Strikes!
Painted and Getting Ready
Build Thread - 125 - Took Forever But Here It is!
That's a large amount of info. I hope grandma is comfortable as possible. May her passing come with ease and much comfort to those who love her. I watched my dad pass from small cell cancer. He went peacefully. Happy quail farming. Spoiled doggos you got there. Sunny loves slightly cooked...www.reef2reef.com
Tank is Inside
Plumbing, Rockwork,and Sand Added
Build Thread - 125 - Took Forever But Here It is!
She could be... If she survives long enough to eat the fish and shrimp she might greatly reduce the waste for a short time...at least until she adds her waste or becomes part of the waste at which time there may be a significant ammonia spike. I wonder if cat food is low in phosphates...
Aragocrete frag rack project walk-through
Build Thread - 125 - Took Forever But Here It is!
Yep. I told her that the box is full of live animals. She said I can expect it tomorrow. I said "What good is a box full of dead animals?" Exactly. I've had those conversations with shippers. One of the reasons i hate ordering.
DISCLAIMER: THIS 125 TANK IS STILL RUNNING. HOWEVER, I won an ESHOPPS Mariner 70 so I'm going to have a build for that and don't want to lose this one. This is still my main build thread until I decide it's not?
Build Thread - ESHOPPS Mariner 70 Build
Alright. I'm going to get this started! I won the ESHOPPS Mariner 70 giveaway so I'm setting up the build thread. Pictures will be coming as I set it up! Equipment List: Obviously, ESHOPPS Mariner 70 ESHOPPS RS-100 sump ESHOPPS S-120 Protein Skimmer and ESHOPPS Lift Skimmer Stand Rio+ 2100...
OP
OP
tbrown
Nominated Cronie Intern - Might be failing?
It's about to un-turn out. I'm in the middle of a tank transfer.
It's saying "just the tip".Why?
Fish Styx
In Cod We Crust
Partner Member 2024
Reef Tank 365
RGB
Hospitality Award
Reef Pumpkin Carver
WAMAS
Rock Pool Reef Keepers
R2R Secret Santa 2023
My Tank Thread
My Aquarium Showcase
stoney7713
10K Club member
Well I'm down.
Extruder quit this morning, I done everything I could. Contacted creality support, 20 minute wait on replies, I finally got a support ticket, they said to give them at least 5 days and if I don't hear anything to reach out again.
Extruder quit this morning, I done everything I could. Contacted creality support, 20 minute wait on replies, I finally got a support ticket, they said to give them at least 5 days and if I don't hear anything to reach out again.
Sorry about that. Is also frustrating costumer service.
OP
OP
tbrown
Nominated Cronie Intern - Might be failing?
Did you check the wires to make sure nothing came unsoldered?
stoney7713
10K Club member
I've heard the stories. I just hope they agree just to send me a new extruder.
Bambu keeps showing the P1S and AMS as presale. I guess I'll place my order and wait.
stoney7713
10K Club member
Yup disassembled and checked everything.
stoney7713
10K Club member
Also had the main board cooling fan go out about 6 months ago, I just replaced it myself. That was quick, easy and cheap.
stoney7713
10K Club member
I've read a few cases where they simply supplied the broken part.
But there are sooooo many more, lack of resolution.
I did buy an extended warranty because of all the bad stories of warranty, so if there's no fix from creality I can use it
Pretty please could you share the stl?Took awhile but I got it covered
stoney7713
10K Club member
Yeah let me get it zipped up. @tbrown maybe you should try it too, it's a quick and easy manual filament change, just set it in your slicer.
Similar threads
