3x3 Reef Savvy

[truepercs]

Thanks…

The Algae, I have not found anything. One of the reasons I was hoping to upgrade one day.

I want to add a tang or two to see if it will help. I have been pulling it out when it is bad.

 

[truepercs]

Plumbing was much more difficult than I thought it would be. I had to redo due to
Leaks. The aquarium is in our family room and on the hard wood floors.

Finally got it as needed.
Now to tackle a light fixture or mounting brackets for my light
There is still algae on the rocks now…

I will get to it, hoping to add some new fish first to see if it helps.

The algae is a pain

 

[Gumbies R Us]

Best of luck with the new fish!

 

[truepercs]

I bought a Maxspect pump
and controller from the marketplace… Bought another pump to run two since one is not enough only to find that the controller is not working properly. Probably will get burned on this purchase.

I was looking for alternatives, my MP 40’s keep falling off the thicker glass. MP60 is pricey, I was hoping for another option. At this point Maxspect support has not been helpful. I was hoping that at least I could get it fixed at a cost lower than replacing the controller. Let’s see if this changes…

At least when I had issues with the Ecotech I could send in for repairs… or they would provide a discount on a new one if it could not be repaired.

 

[Sleeping Giant]

cool looking tank

 

[Tarantula424]

Very unique look with the tank on the cart. I'd be interested to see a little more of your plumbing. Great work.

 

[truepercs]

I have a sump in the basement… along with my controller top off etc…
This is the plumbing upstairs. It just dumps into a typical sump. I also have a water change station right by the sump.

I still plan to paint the plumbing a bit to blend in…

I need to mount my light first, may try to get that done this weekend.

Plumbing is straight, pictures make it look a bit off

The wood back there is my temp light bracket

 

[truepercs]

I received a response from the seller of the pump, he is assisting as he may have registered the pump. I provided him with the support information required. Hopefully i can get this resolved. That was nice of him to respond, I understand it is used however it was sold as new condition. Even if I have to pay a small fee to get repaired it will be fine. I just don’t want to have to buy a new unit otherwise I would have just bought all new

 

[truepercs]

After a few messages back and forth with the seller of the pump. We came across options to get the second pump running on the controller. I have it working so all is good.

 

[Tarantula424]

I have a sump in the basement… along with my controller top off etc…
This is the plumbing upstairs. It just dumps into a typical sump. I also have a water change station right by the sump.

I still plan to paint the plumbing a bit to blend in…

I need to mount my light first, may try to get that done this weekend.

Plumbing is straight, pictures make it look a bit off

The wood back there is my temp light bracket

Looks like really nice work to me. Glad to see some 45's on the drain side. Is the one that runs on top 1.5 inch and the one right under 1 inch? If so did it add any difficulty dialing in the Herbie?

 

[truepercs]

So far all is working fine. Although a bigger return pump is in my future.

Also think I will need more flow from power heads

 

[truepercs]

I still have not mounted my lights properly. I really need to do this soon.

I opted to go another route instead of Tangs… At least for the time being…

I placed an order from Harry’s Marine Life
For a trio of Watanabie Angels. They are currently in a QT tank that I had matched salinity of the delivery and have been using my DOS to slowly add tank water to match the salinity of the display. They appear to be eating, and look healthy. So I believe I may be able to add to display tomorrow.

To play it safe I will try to catch and isolate my Tomani Tang to avoid any unneeded stress.