Apex TRIDENT NP not working, help please! (customer service will not help)

Crab Killer

New Member
View Badges
Joined
Jan 14, 2023
Messages
5
Reaction score
0
Location
Next to my fish tank
What state or country do you live in
Maryland
Rating - 0%
0   0   0
I bought a new Apex and Trident NP and flow meters. The Trident NP just says "initializing" for 5 hours. The status light stays solid blue and it clicks every now and then but just stays in that state.

I tried unplugging it and then tried again for a couple hours this time and the same thing.

I tried updates also, nothing helps.

I tried to get help from Neptune and finally after 1.5 hours waiting on the phone someone answered and told me to send pictures of the front status light and also inside the machine and also the serial number. I sent all of that by email and can not get a single response at all from them. Each day a sent a follow up asking if they would help and that and its been over a week and 5 emails to them and no response at all from them. I guess they do not help with trouble shooting the equipment.

Is there anyone here that can give me some advice as to what might be the problem or what can help to get it to work?

Thanks in advance! I really appreciate and advice that you have!
 
If you bought it new and its not working and they aren't helping I would just return it. I've never used one but I've read more negative experiences than positive.

PS. If support can't help get it running what happens when it fails after you become dependent upon it, assuming you get it online? Support is more important than price to me on equipment like that.
 
If you bought it new and its not working and they aren't helping I would just return it. I've never used one but I've read more negative experiences than positive.

PS. If support can't help get it running what happens when it fails after you become dependent upon it, assuming you get it online? Support is more important than price to me on equipment like that.
It looks like you are right, I thought that Neptune was a good company but it looks like my purchase was a huge mistake.

Ive now tried called them 2 more times, they never a picked up, just had me on hold. I gave up after 1 and a half hours on one call and 1 hour on the other.

Ive sent 2 more emails and no response at all.

This is absolutely the worse customer service that I have ever seen in my entire life. I would rather them respond and say that they are not going to help instead of me waiting many many hours trying to contact them.

Thanks for you opinion, I appreciate it.
 
Couple of questions maybe will help

1) Do you see the NP in your APEX app/GUI?
2) Where is the 1Link plugged into? If it's plugged into the powerbar, check whether the powerbar is blinking. If you have it plugged into a 1Link module, make for certain you have the 12V power plugged into that as it will not be able to send control signal back to the APEX.
3) Unplug everything from the powerbar and do a hard reset on that in order to hard reset the APEX. You may have a conflict in the port assignments and starting from scratch with the system may clear that and allow it to initialize.
4) Download Grok Bots (seriously), give it access to APEX, and let it figure out the problem. No - I'm not kidding. This works amazingly in helping to find where the conflict is sitting for many programs and peripherals. They are also excellent at helping setup customization that you would need a good deal of programming knowledge to be able to do otherwise.
 
I have had a NP for over a year. The only issue I have had is when I let it idle without reagents for a couple of weeks and some of the reagent/salt precipitated in the tubing. Once I cleaned it out and recalibrated, it was back to normal. I also run the cleaning cycle every reagent change even if it doesn't call for it. Other than that, it's dead on to Hanna checkers with both NO3 and PO4.
 
I have had a NP for over a year. The only issue I have had is when I let it idle without reagents for a couple of weeks and some of the reagent/salt precipitated in the tubing. Once I cleaned it out and recalibrated, it was back to normal. I also run the cleaning cycle every reagent change even if it doesn't call for it. Other than that, it's dead on to Hanna checkers with both NO3 and PO4.

Whenever I am not using a trident ACM or NP, I fill the reagent bottles with rodi water and let the unit run its normal testing.
No salt crystals, no tearing it down and then setting it up again etc.

Regarding testing results, I am confident and have matched it against many kits and is pretty close within margin of error.
 
Whenever I am not using a trident ACM or NP, I fill the reagent bottles with rodi water and let the unit run its normal testing.
No salt crystals, no tearing it down and then setting it up again etc.

Regarding testing results, I am confident and have matched it against many kits and is pretty close within margin of error.
Great idea!
 
Great idea!
Make sure to prime everything once you do bring it back online with actual reagents, Even if you dont prime reagents first results or two will be off due to rodi water in the lines but then it will start showing true results.
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 17 30.4%
  • I’d trust someone who knows my tank to choose

    Votes: 2 3.6%
  • I’d rather get a gift card and pick it myself

    Votes: 22 39.3%
  • I’d prefer gear or supplies instead

    Votes: 0 0.0%
  • Please don’t surprise me with livestock

    Votes: 15 26.8%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new