Contemplating Building My Own tank

SasquatchReefer

Community Member
View Badges
Joined
Apr 27, 2021
Messages
47
Reaction score
17
Location
South
What state or country do you live in
Florida
Rating - 0%
0   0   0
I am looking to upgrade my current tank which is about 60 gallons.

I have the space to go with a tank that is approximately 8ftx2ftx2ft.

I reached out to a few aquarium builders and have been quoted $3400 for 1/2” with a 12 week wait time…

I’m going to reach out tomorrow to a few local acrylic suppliers to see how much a few sheets of 3/4” acrylic would be.

i would like the top to be as open as possible, would I still need cross braces on my euro brace with 3/4” acrylic? Or should I jump to 1”?
 
@UncommonSense, I hope you don't mind me tagging you, but I feel like you are the right person to ask here.
 
I am looking to upgrade my current tank which is about 60 gallons.

I have the space to go with a tank that is approximately 8ftx2ftx2ft.

I reached out to a few aquarium builders and have been quoted $3400 for 1/2” with a 12 week wait time…

I’m going to reach out tomorrow to a few local acrylic suppliers to see how much a few sheets of 3/4” acrylic would be.

i would like the top to be as open as possible, would I still need cross braces on my euro brace with 3/4” acrylic? Or should I jump to 1”?
For rimless acrylic, 96” long, and 24” tall?

My spidey senses say 1” at minimum, but I don’t do a ton of acrylic work, so let’s see if the pros like @Troylee, or @Joe Glass Cages may have a more concise answer for you!
 
I don’t think 1” is going to do it at the span and height. Failure isn’t the concern. Bowing and deflection are. I’m not where I can do the math, but I suspect the deflection will be significant over time.
 
Last edited:
I don’t mind doing a eurobrace 3-4” continuous around the perimeter, i was just trying to prevent needing a eurobrace + cross bracing
 
Last edited:
I am looking to upgrade my current tank which is about 60 gallons.

I have the space to go with a tank that is approximately 8ftx2ftx2ft.

I reached out to a few aquarium builders and have been quoted $3400 for 1/2” with a 12 week wait time…

I’m going to reach out tomorrow to a few local acrylic suppliers to see how much a few sheets of 3/4” acrylic would be.

i would like the top to be as open as possible, would I still need cross braces on my euro brace with 3/4” acrylic? Or should I jump to 1”?

I don’t mind doing a eurobrace 3-4” continuous around the perimeter, i was just trying to prevent needing a eurobrace + cross bracing

Have you considered a Floridian based acrylic tank maker or are you set on building the tank yourself?
 
For rimless acrylic, 96” long, and 24” tall?

My spidey senses say 1” at minimum, but I don’t do a ton of acrylic work, so let’s see if the pros like @Troylee, or @Joe Glass Cages may have a more concise answer for you!
will need cross braces with acrylic at 24 tall.
 
I would say DIY is a rather ambitious project at that size. The materials are expensive and heavy, and with the VOC based changes in bonding products, they are far less forgiving than they used to be. I'm not sure even with my experience and tooling that I would take a tank on that size anymore.
 
Do you have someone you recommend?
There are a couple Floridian-based builders that I would recommend: Tsunami Aquariums from Clearwater and Acrylic Habitats from Poinciana.
 
I am looking to upgrade my current tank which is about 60 gallons.

I have the space to go with a tank that is approximately 8ftx2ftx2ft.

I reached out to a few aquarium builders and have been quoted $3400 for 1/2” with a 12 week wait time…

I’m going to reach out tomorrow to a few local acrylic suppliers to see how much a few sheets of 3/4” acrylic would be.

i would like the top to be as open as possible, would I still need cross braces on my euro brace with 3/4” acrylic? Or should I jump to 1”?
This is the results from one of the on line calculators for GLASS. Approx 3/4" floor, 1/2" sides
This is for un-braced.
Depth of tank is really the driving factor.

Not sure if acrylic would need to be thicker (think the opposite is true)
apparently it isn't as "stiff" as glass soo
I'd eurobrace anything to add a safety factor.
Oh yea believe you need cell cast acrylic.

And this large of acrylic requires a specific type of "glue" (2 part epoxies I believe) over the simple solvent weld types.
Consider this just an FYI for further research.

Screenshot 2026-11-18 142733.png


For "fun" from our new overlords..
AI Overview


You can calculate the required acrylic thickness and panel dimensions using the Acrylic Tank Thickness Calculator from American Acrylics or the ACRYLITE® Aquarium Calculator. [1, 2]

Key Factors in Acrylic Aquarium Calculation
    • Water Height (Depth): Hydrostatic pressure increases directly with water depth, meaning panel thickness is determined by how tall the water column is rather than overall tank volume. [1, 2, 3]
    • Cell-Cast vs. Extruded: Always use cell-cast acrylic for aquariums; extruded acrylic is weaker, prone to crazing, and should never be used for pressure-bearing tanks. [1, 2]
    • Safety Factor: Standard aquarium designs apply a high safety factor (typically around 10:1 working stress vs. ultimate strength, or lower multiplier depending on engineer rules) to account for bowing and joint stress. [1, 2]
    • Bracing: A properly braced or euro-braced top perimeter significantly reduces panel deflection. Unbraced or extra-tall tanks (over 24 inches) require professional engineering review. [1]
Surprising to me that the 2 acrylic calculators recommend thicker material than glass.
Screenshot 2026-11-18 145713.png
 
Last edited:
I ran the "ask the overlord" again..rimless..

For a 96" × 24" × 24" rimless acrylic aquarium (a standard 240-gallon footprint), removing top bracing dramatically increases the required panel thickness to prevent severe bowing over an 8-foot span. While standard Euro-braced 96" × 24" × 24" acrylic tanks are typically built with 1/2" to 3/4" cell-cast acrylic, a true rimless build at this length and height generally requires 1.25" to 1.5" (32 mm to 38 mm) cell-cast acrylic on the vertical walls. [1, 2]


Estimated Calculator Outputs (96" × 24" × 24" Rimless)

  • Recommended wall thickness: 1.25" to 1.5" cell-cast acrylic is typically needed to keep deflection (bowing) within safe limits on an unsupported 8-foot span. Using 1/2" or 3/4" without a top perimeter flange will cause noticeable bowing and stress the top corner seams. [1]
  • Nominal external volume: 239.4 gallons (commonly sold as a 240-gallon tank). [1]
  • Actual internal water volume: Roughly 190 to 205 gallons, once you subtract 1.25"–1.5" wall thicknesses, a 1" bottom panel, a 1.5"–2" water-line gap at the top, and displacement from rock or substrate.
  • Water weight alone: About 1,585 to 1,710 lbs (at 8.34 lbs per gallon).
  • Total filled weight: Roughly 2,100 to 2,500+ lbs once you include the heavy acrylic panels (around 450–550+ lbs for thick rimless sheets), substrate, rock, stand, and sump.


Key Design Trade-Offs for an 8-Foot Rimless Acrylic Tank

  • Acrylic vs. Glass for rimless: Acrylic is more flexible than glass, meaning an unsupported 8-foot rimless acrylic panel deflects visibly unless you step up to very thick, expensive cast sheets. Many builders choose low-iron glass (typically 3/4" / 19 mm) for a true 96" × 24" × 24" rimless tank, or add a thick 1" Euro-brace to an acrylic build to keep the wall thickness at 3/4".
  • Full bottom support: Regardless of wall thickness, an acrylic aquarium must sit on a completely flat, solid top surface (such as 3/4" plywood with a leveling mat) rather than a perimeter-only frame.
  • Cost and fabrication: Thick 1.25"–1.5" cell-cast acrylic requires specialized solvent bonding and annealing, which places a custom 8-foot rimless acrylic build well above standard braced 240-gallon pricing (standard braced 96" × 24" × 24" acrylic tanks generally start around $3,000–$3,600). [1]
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 15 35.7%
  • I’d trust someone who knows my tank to choose

    Votes: 1 2.4%
  • I’d rather get a gift card and pick it myself

    Votes: 14 33.3%
  • I’d prefer gear or supplies instead

    Votes: 0 0.0%
  • Please don’t surprise me with livestock

    Votes: 12 28.6%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new