Got my ICP test and......I am confused.......

  • Thread starter Thread starter BanZI29
  • Start date Start date
  • Tagged users Tagged users None

BanZI29

Still just a reefer noob!
View Badges
Joined
Oct 26, 2020
Messages
1,389
Reaction score
2,545
Location
Port St. Lucie
Rating - 0%
0   0   0
Hello all. I got my ICP test and I am confused about a couple of the results. It shows high aluminum, zinc and Iron. I have no idea where it could be coming from either. I am asking for your help figuring this out and maybe why everyone is unhappy. Here is some pictures and the ICP test.
I THINK my tank is on the verge of a crash and I am trying to stop it. The pix of my tank (everyone is ticked, hence the reason for this post) and the params are as of this post.
temp = 77.4°
Salinity = 1.025 scope
pH = 8.04 hanna
Ammonia = 0 API
Nitrite = 0 Hanna
Nitrate = 12.4 Hanna
Phos = .034 Hanna
Calcium = 420 red sea
Mag = 1230 Auquaforest
RODI TDS = 0 amazon tester

Filtration: filter floss, Matrix rock, (for bacteria), bag of carbon ( put in recently because of this current problem) reactor with Chemipure blue, skimmer.
I also have 2 550GPH pumps at 3/4 power.

Thank you for any help you all can give.
1686511307344.png
1686511390418.png
1686511446757.png
1686511480980.png
1686511540778.png
1686511578233.png
1686511614368.png
20230611_151701_HDR.jpg
20230611_151711_HDR.jpg
20230611_151716_HDR.jpg
20230611_151721_HDR.jpg
20230611_151729_HDR.jpg
20230611_151738_HDR.jpg
20230611_151743_HDR.jpg
20230611_151749_HDR.jpg
1686511432270.png
 
Check all your magnets and make sure none are exposed and rusting. I also know that the bio rocks are a common source of aluminum on ICP tests.

Other than that po4 is a little on the low side. You're also running double carbon essentially by running carbon and chemipure blue.
 
Check all your magnets and make sure none are exposed and rusting. I also know that the bio rocks are a common source of aluminum on ICP tests.

Other than that po4 is a little on the low side. You're also running double carbon essentially by running carbon and chemipure blue.
Yea I know, I did that because I THINK the last water change, my tanks had something int hem that contaminated my water when I changed it. I put it in there to hopefully take out whatever was contaminating.
And the mags, I didn't even think about those. I will look now.
 
Do you use bleach to clean equipment? If so, make sure it’s not splashless. I made that mistake which spiked metals in my ICP in the past.
I don't use bleach. That is another post I have on how to clean my water jugs. still haven't gotten any real answers on that
 
Zinc and iron are the 2 that are on the highest side .
I would lean towards metal clamps , exposed magnets , but would also test those levels in a batch of fresh saltwater before your next water change
 
How much of a factor is iodine? Don’t really have any corals but I see that pop up some times and OPs is a little low too
 
How much of a factor is iodine? Don’t really have any corals but I see that pop up some times and OPs is a little low too
I am not sure either. I know that if you have a sick coral you can dip them in it. but I think its just a trace element that does not have a major effect on corals
 
So I had these magnet frag ledges and... the magnets are exposed on the back. SO most likely the culprit of the high metals? I had 4 of these.
20230611_204115_HDR.jpg
Makes sense to me, maybe take them out and laser if the heavy metal absorbers start lowering your levels.

Maybe you can epoxy them so they aren’t a total waste?
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new