Happened again......

[ithk21620]

I have the ph in the co2 already connected to the PH2 on my apex. Would I be able to ise that, instead of buying a new pm1?

Yes that work too. I didnt have an open PH slot on my Apex so that is why I use a PM1 module.

Here is what I use for my code (The PH numbers would be adjusted up or down depending on your needs):
Fallback OFF
If CaRxPH > 7.10 Then ON
If CaRxPH < 7.00 Then OFF

 

[renato120]

Yes that work too. I didnt have an open PH slot on my Apex so that is why I use a PM1 module.

Here is what I use for my code (The PH numbers would be adjusted up or down depending on your needs):
Fallback OFF
If CaRxPH > 7.10 Then ON
If CaRxPH < 7.00 Then OFF

Im gonna buy a selenoid now. Thank you.

 

[3mm3]

I would stick with the Ca Reactor. I made the mistake of going to a doser from my reactor once and now I am back to the reactor. I know exactly what you mean by the dripper getting clogged and its very frustrating always screwing around with the output. Watch this video and try this method, it works good.

Another option would be to get a Masterflex Peristaltic Pump or similar to use for feeding your reactor. The drip would stay constant then. Before you go this route I would do some research about using the Masterflex pumps since there are many different Masterflex pumps and you will want to pull the water through the reactor versus feed the reactor.

Excellent video. This method is very good and what I have used for years.

 

[renato120]

I would stick with the Ca Reactor. I made the mistake of going to a doser from my reactor once and now I am back to the reactor. I know exactly what you mean by the dripper getting clogged and its very frustrating always screwing around with the output. Watch this video and try this method, it works good.

Another option would be to get a Masterflex Peristaltic Pump or similar to use for feeding your reactor. The drip would stay constant then. Before you go this route I would do some research about using the Masterflex pumps since there are many different Masterflex pumps and you will want to pull the water through the reactor versus feed the reactor.

@Gui Paim

 

[renato120]

Yes that work too. I didnt have an open PH slot on my Apex so that is why I use a PM1 module.

Here is what I use for my code (The PH numbers would be adjusted up or down depending on your needs):
Fallback OFF
If CaRxPH > 7.10 Then ON
If CaRxPH < 7.00 Then OFF

Do I need to connect the solenoide to an apex energy bar, or can it be any outlet? My apex energy bars are all full. If it needs to be connected to it, then I will need to buy a new one.
Thanks again. It stopped again this night. Its crazy.

 

[ithk21620]

Do I need to connect the solenoide to an apex energy bar, or can it be any outlet? My apex energy bars are all full. If it needs to be connected to it, then I will need to buy a new one.
Thanks again. It stopped again this night. Its crazy.

You will need to connect it to your Apex energy bar so that you can turn the flow off and on depending on the PH.

Another option would be to buy one of these and use it to turn the solenoid on and off as needed. Then you wouldn't need to purchase another EB8 but you wouldn't be able to see what was going on with your reactor from afar.
http://www.bulkreefsupply.com/milwaukee-mc122-ph-controller.html

 

[renato120]

You will need to connect it to your Apex energy bar so that you can turn the flow off and on depending on the PH.

Another option would be to buy one of these and use it to turn the solenoid on and off as needed. Then you wouldn't need to purchase another EB8 but you wouldn't be able to see what was going on with your reactor from afar.
http://www.bulkreefsupply.com/milwaukee-mc122-ph-controller.html

Ok got it! Im still looking for a solenoid that will fit my regulator.

 

[ithk21620]

Ok got it! Im still looking for a solenoid that will fit my regulator.

Something like this should work for you. You can just cut your co2 line after the regulator and install it inline.
http://www.bulkreefsupply.com/milwaukee-ma955-co2-solenoid-valve.html

Otherwise you will need to find out what size threaded connection your regulator excepts and then buy one to fit

 

[renato120]

Something like this should work for you. You can just cut your co2 line after the regulator and install it inline.
http://www.bulkreefsupply.com/milwaukee-ma955-co2-solenoid-valve.html

Otherwise you will need to find out what size threaded connection your regulator excepts and then buy one to fit

I think I Bought everything.
Neddle wheel valve
EB 8
Solenoid
Hopefully everything will be here by Monday.
Thank you sooo much for the help and pacience!

 

[renato120]

@ithk21620 I got all the parts today to do this. I installed. Im lost here.
I have the output running... not dripping
My tank PH is low since I got the calcium reactor.
Its at 7.9.
I dont think I can start at 7.1 and shut off at 7.0
Im all lost here. The solenoid turns on, 7.1 but doesnt turn off at 7.0. Im not sure on how to setup. How much co2 bubbles should be.
Help please.

 

[ithk21620]

@ithk21620 I got all the parts today to do this. I installed. Im lost here.
I have the output running... not dripping
My tank PH is low since I got the calcium reactor.
Its at 7.9.
I dont think I can start at 7.1 and shut off at 7.0
Im all lost here. The solenoid turns on, 7.1 but doesnt turn off at 7.0. Im not sure on how to setup. How much co2 bubbles should be.
Help please.

The tank PH doesn't matter, its the PH inside the ca reactor. I also wouldn't start at 7.1-7.0 I would start more like 7.5-7.6 and work your way down over time so you don't cause an Alk spike.

You will need to program an outlet on the EB8 that will turn on and off depending on the PH inside the reactor. I believe you were going to do this off or your PH2 probe on your apex. You will need something like this:

Fallback OFF
If (Whatever your PH probe is called) > 7.60 Then ON
If (Whatever your PH probe is called) < 7.50 Then OFF

Also the CO2 bubbles don't matter much but I would run them at 1-2 per second so you don't flood the reactor with CO2 and cause the valve to continually short cycle.

Without seeing your exact setup its hard to see what is wrong exactly. Can you post a couple pictures? Post your coding of your apex?

 

[renato120]

So I set up to turn on at 7.3, and shut off at 7.2.
Bubble rate at 2 per second.
Right now my calcium reactor PH is at 6.34
I was trying to figure out, and it dropped a lot.
So the calcium reactor is running with the co2 bubbles off right now. Only the output is running. That means no CA and ALK are Going in the tank correct?
My undestanding is that PH raises when co2 bubbles are off. As soon as it turns on CA and ALK dump in the water and lower PH.
@ithk21620

 

[ithk21620]

So I set up to turn on at 7.3, and shut off at 7.2.
Bubble rate at 2 per second.
Right now my calcium reactor PH is at 6.34
I was trying to figure out, and it dropped a lot.
So the calcium reactor is running with the co2 bubbles off right now. Only the output is running. That means no CA and ALK are Going in the tank correct?
My undestanding is that PH raises when co2 bubbles are off. As soon as it turns on CA and ALK dump in the water and lower PH.

As the PH drops in the reactor the media melts creating Ca and Alk. With your reactor at 6.34 right now the media is releasing ca and alk but the reactor will gradually increase in PH. Just let it run and watch to make sure the bubbles come back on when it hits 7.3 and then **** off at 7.2

Once you know it is working correctly you will want to let it run for a few days so the tank settles down and you can see exactly what is going on. Like I said I started high and adjusted every week to two weeks until the tank went at least a week without dropping in alk