Matching Equipment Stand for Red Sea Reefer

[mrsaltwaterguy]

I'm looking to build or modify an existing stand to match my red sea reefer 450 to hold all of my equipment. Any advice appreciated!

 

[nautical_nathaniel]

I think the toughest part is going to be finding the right exterior material to match the outside of the red sea stand. I would focus on finding that and get enough to do a veneer or shell around a wood frame to keep things simple.

 

[293482398]

The Ikea Eket stands matches the finish quite well, a cheap + easy solution. They're cheap enough, you could use it temporary.

https://www.ikea.com/us/en/catalog/products/90333938/

 

[mrsaltwaterguy]

The Ikea Eket stands matches the finish quite well, a cheap + easy solution. They're cheap enough, you could use it temporary.

https://www.ikea.com/us/en/catalog/products/90333938/

I just wish it came in black so it would match.

 

[Citycop89]

Look up a black melamine sheet/panel product

 

[Zeal]

The Ikea Eket stands matches the finish quite well, a cheap + easy solution. They're cheap enough, you could use it temporary.

https://www.ikea.com/us/en/catalog/products/90333938/

Sorry but I dont think I trust Ikeas build quality to hold a tank that weighs hundreds of pounds..

 

[Water Dog]

Sorry but I dont think I trust Ikeas build quality to hold a tank that weighs hundreds of pounds..

See the OP, these are suggestions for an equipment cabinet, not a tank stand. That said, check out these new stands from Petco. I think these will match your Reefer stand quite nicely.

https://www.petco.com/shop/en/petcostore/product/imagiatrium-black-gloss-fish-tank-stand#

https://www.petco.com/shop/en/petco...-gloss-fish-tank-stand-up-to-40-gal?rrec=true

Here it is in white so you can see the detail...

https://www.petco.com/shop/en/petcostore/product/imagiatrium-white-gloss-fish-tank-stand?rrec=true#

 

[mrsaltwaterguy]

See the OP, these are suggestions for an equipment cabinet, not a tank stand. That said, check out these new stands from Petco. I think these will match your Reefer stand quite nicely.

https://www.petco.com/shop/en/petcostore/product/imagiatrium-black-gloss-fish-tank-stand#

https://www.petco.com/shop/en/petco...-gloss-fish-tank-stand-up-to-40-gal?rrec=true

Here it is in white so you can see the detail...

https://www.petco.com/shop/en/petcostore/product/imagiatrium-white-gloss-fish-tank-stand?rrec=true#

Exactly what I'm looking for. Thanks!

 

[pelphrey]

I started out with a cabinet from amazon. I didn't like it much and it was a pain to pull cables in and out of.

So I built my own you can see here post 383 - https://www.reef2reef.com/threads/devoted-reefer-250.263426/page-20

 

[TX_Punisher]

What did you decide on this? I’m thinking of adding a frag tank next to my 750 and want it to match.

 

[TX_Punisher]

What did you decide on this? I’m thinking of adding a frag tank next to my 750 and want it to match.

 

[bxchris]

The Ikea Eket stands matches the finish quite well, a cheap + easy solution. They're cheap enough, you could use it temporary.

https://www.ikea.com/us/en/catalog/products/90333938/

Bought it. Now I need to figure out how to modify.

 

[Water Dog]

Bought it. Now I need to figure out how to modify.

What is your intended use for the cabinet? To house your controller or general equipment storage?

 

[bxchris]

What is your intended use for the cabinet? To house your controller or general equipment storage?

Hey Water! Apex controller. Hope to keep als much electrical equipment out of the tank stand as possible

 

[Water Dog]

Although not the referenced Petco Imagitarium cabinet the concept is the same. This is where a drill, a pocket jig and some wood glue really come in handy. I used 3/4 inch plywood to make a controller board that inserts inside of my Amazon glass door cabinet. I painted the controller board with gloss acrylic paint. Hope this helps! :)

 

[bxchris]

Although not the referenced Petco Imagitarium cabinet the concept is the same. This is where a drill, a pocket jig and some wood glue really come in handy. I used 3/4 inch plywood to make a controller board that inserts inside of my Amazon glass door cabinet. I painted the controller board with gloss acrylic paint. Hope this helps! :)

That's awesome! So how does the board attach to the cabinet? Also is the board mounted to the back of the cabinet or is there a space?

 

[bxchris]

That's awesome! So how does the board attach to the cabinet? Also is the board mounted to the back of the cabinet or is there a space?

Oh I see it's mounted to another piece of plywood so it's free standing. That gives you the space behind. Is it a nail straight through those triangular pieces?

 

[Water Dog]

Yes, the control board is freestanding and slips right into the cabinet. I used a pocket jig to join the two boards together with screws along with a healthy bead of wood glue between the joint. The 4 triangle pieces are just glued on for additional support. The space behind the board is where I mounted power bricks and such.

 

[bxchris]

Yes, the control board is freestanding and slips right into the cabinet. I used a pocket jig to join the two boards together with screws along with a healthy bead of wood glue between the joint. The 4 triangle pieces are just glued on for additional support. The space behind the board is where I mounted power bricks and such.

Got it! Thanks for the help.

 

[AZMSGT]

I took an Ikea cabinet and did this to it. It’s Dark brown.. but so dark it’s practically black.

https://m2.ikea.com/us/en/p/havsta-cabinet-with-base-dark-brown-20391050/