Milwaukee MA887 reading off?

  • Thread starter Thread starter b4tn
  • Start date Start date
  • Tagged users Tagged users None

b4tn

Valuable Member
View Badges
Joined
Jun 17, 2015
Messages
1,679
Reaction score
2,227
Location
Columbia MD
Rating - 0%
0   0   0
I ran out of calibration fluid for my Milwaukee so I re filled it with RO/DI and have been using it like this for some time. Out of curiosity today I put some of the 1.025 fluid on it and it read 1.028? I have not used It in probably well over a year or more but honestly don’t recall the reading I got with it before. I put bottled water on the meter and got 0 just like the RO/DI sample. My tank reads 1.026 but that’s where I keep it based on the meter. Could my 1.025 fluid be expired or off? It’s always had the lid on it so it shouldn’t be evaporation. I noticed a small scratch on the prism could that be an issue?
e6716ad8cd5b7cc14eac8c14f3603a84.jpg
 
Last edited:
I ran out of calibration fluid for my Milwaukee so I re filled it with RO/DI and have been using it like this for some time. Out of curiosity today I put some of the 1.025 fluid on it and it read 1.028? I have not used It in probably well over a year or more but honestly don’t recall the reading I got with it before. I put bottled water on the meter and got 0 just like the RO/DI sample. My tank reads 1.026 but that’s where I keep it based on the meter. Could my 1.025 fluid be expired or off? It’s always had the lid on it so it shouldn’t be evaporation. I noticed a small scratch on the prism could that be an issue?

Mine always reads 1.027 when I use calibration fluid I thought it was normal and accounting for the error when testing. I use a refractometer to double check.
 
I had an issue when I first got mine that the reading were constantly off, including the reference fluid. take a Qtip and put some windex on it and clean the sensor really good, then follow up with some RODI. (these were instructions as per Milwaukee, I called them) and try the reference fluid again. they basically said my sensor was dirty even though I thought it was clean
 
I had an issue when I first got mine that the reading were constantly off, including the reference fluid. take a Qtip and put some windex on it and clean the sensor really good, then follow up with some RODI. (these were instructions as per Milwaukee, I called them) and try the reference fluid again. they basically said my sensor was dirty even though I thought it was clean

I’m gojng to try this tomorrow good idea.

Did this correct the error issue?
 
the 1.025 calibration fluid always reads 1.026 off a bit but not enough to complain about. Perhaps some of the fluid evaporated over time ? Clean it with a 99% isopropyl alcohol not windex.
 
I have verified this with multiple Milwaukee meters. It is very consistently high in readings. If you properly calibrate a refractometer with a known good calibration fluid, it reads high with the Milwaukee. Oddly, the Hanna version of this same meter was spot on, but I have only tested one of those.

My meter reads 1.028 with 1.026 calibration fluid. So I shoot for 1.028. This is confirmed with a refractometer and my salinity probe on my Apex.

3a618288dc37d8c1e35ac8e9a5bbd07a.jpg
 
I always got high readings and ended up selling mine. I just didn't trust it.
 
I think my calibration fluid evaporated a bit.. mine reads 1.027 with the 1.025 calibration fluid. I had my salinity validated at the LFS and it was 1.025 there vs the unit reading 1.026. Who knows! Close enough though lol.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 17.7%
  • Fish or coral food

    Votes: 5 5.2%
  • Test kits or reagents

    Votes: 10 10.4%
  • Filter media or replacement fleece

    Votes: 5 5.2%
  • RO/DI filters or supplies

    Votes: 15 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 12 12.5%
  • I keep a backup of everything

    Votes: 25 26.0%
  • Other (Post in the comments)

    Votes: 7 7.3%
Back
Top
Home
Post thread…
Market
What's new