Peristaltic pumps and Kalk Reactors

  • Thread starter Thread starter Sebae
  • Start date Start date
  • Tagged users Tagged users None

Sebae

Active Member
View Badges
Joined
Jul 5, 2017
Messages
120
Reaction score
44
What state or country do you live in
Florida
Rating - 0%
0   0   0
Hello all,

I'm currently using a Kamoer dosing pump to feed RO/DI water to my Avast Kalk Reactor which does 8 liters per day in a total of 24 doses (333 mL every hour).

I've had one pump fail from what I presumed was either bad luck or too much dosing volume. I switched to another doser on the unit and it failed this morning.

Does anyone else have experience dosing large volumes through peristaltic pumps? Is this a likely cause of the problem? Would anyone happen to have recommendations to solve this issue?

Thanks
 
Which one are you using? Some peri pumps are designed for continuous use, others are not. What failed? Heads and tubing need periodic replacement. If the motor failed, then clearly the pump isn’t up to the task you are asking of it. Hard to offer much in the way of advice absent key details.
 
I'm using the Kamoer x4 WiFi doser. I believe it is the motor that failed.

I'm guessing it isn't up to the task of continuous dosing. I didn't know there were continuous pumps and non-continuous.

Thanks for the reply and probably solution
 
You shouldn't need a continuous duty peristaltic pump for a Kalk reactor, assuming it is not dripping Kalk 24 hrs a day. That being said, if you have the space (or can conceal it) a Cole Parmer is what I am using for Kalk dosing. It is extremely precise, tubing is the only thing I will ever need to replace (at about $1 each replacement), and the unit only cost me $150 on eBay.

If this isn't an option I would look at reliable/tried dosing pumps. SpectraPure and GHL come to mind.
 
You shouldn't need a continuous duty peristaltic pump for a Kalk reactor, assuming it is not dripping Kalk 24 hrs a day. That being said, if you have the space (or can conceal it) a Cole Parmer is what I am using for Kalk dosing. It is extremely precise, tubing is the only thing I will ever need to replace (at about $1 each replacement), and the unit only cost me $150 on eBay.

If this isn't an option I would look at reliable/tried dosing pumps. SpectraPure and GHL come to mind.
I’ve used a spectrapure liter meter 3 for kalk for many years. I think it’s great.
 
Do you have an Apex? I use a Spectrapure stand alone Basic Peristaltic Pump in conjunction with my Apex. My Spectrapure stand alone pump doses at a rate of 160 ml/min. So I use this Apex dosing program generator to figure out the programming.

If you don’t run an Apex, then I’d agree with the above that the full Spectrapure Litermeter III is the way to go dor dosing kalk with a peristaltic pump.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.7%
  • Fish or coral food

    Votes: 5 5.5%
  • Test kits or reagents

    Votes: 9 9.9%
  • Filter media or replacement fleece

    Votes: 5 5.5%
  • RO/DI filters or supplies

    Votes: 14 15.4%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.0%
  • I keep a backup of everything

    Votes: 24 26.4%
  • Other (Post in the comments)

    Votes: 7 7.7%
Back
Top
Home
Post thread…
Market
What's new