Plumbing Question for basement sump

  • Thread starter Thread starter Lemec
  • Start date Start date
  • Tagged users Tagged users None

Lemec

Active Member
View Badges
Joined
Sep 8, 2015
Messages
388
Reaction score
113
Location
NW Ohio
Rating - 0%
0   0   0
Ok, hoping some of the plumbing experts, or those that have done a basement sump can answer a few questions...I have a Planet Aquarium tank...it has an external drain that has three 1” drains and then two returns. My dilemma is about the number of holes I need to cut in the floor...my thought was to just cut one hole for the drain, either 2 1/2” or 3” drain (what do I need?) and then have a 1.5” or 2” return that branches into the two 1” returns in the upper corners of the tank. Or, do I need 5, 1” return holes drilled into the floor? Trying to figure out what would be best, and what size of piping I need to install.
 
You can certainly stuff three 1” pvc drain lines into a single larger hole. Upsize as much of the return line to 1 1/2” as you can, and split right at the tank. Upsized return makes a sizable reduction to flow resistance (almost 250 gph in my case).
 
I am no expert but I just re-plumbed to a basement sump. I assume your drilling through wood?

You can get a hole saw blade that's 2 inches in diameter from a home improvement store suitable for wood and cut three holes, use two holes for the drains and one for the return. Run the return line as 1.5 inch PVC and split it up close to the tank into 3/4 inch return lines.

That's just a rough idea, but I did a very similar thing. It also gave me a little extra room around the pipes for RO tubing and an electrical cord which I needed.

I love my basement sump and I hope you will too.
 
That was roughly my idea...I wanted the drains to all fall into the same 2-2.5” line with one line to return the water and split it as it comes out of the floor and into the returns...I found a plumbing website that shows the capacity of these pipes in terms of GPH, it was very helpful!

18927755-A533-4495-977A-69F54B543E84.png
 
Ok, hoping some of the plumbing experts, or those that have done a basement sump can answer a few questions...I have a Planet Aquarium tank...it has an external drain that has three 1” drains and then two returns. My dilemma is about the number of holes I need to cut in the floor...my thought was to just cut one hole for the drain, either 2 1/2” or 3” drain (what do I need?) and then have a 1.5” or 2” return that branches into the two 1” returns in the upper corners of the tank. Or, do I need 5, 1” return holes drilled into the floor? Trying to figure out what would be best, and what size of piping I need to install.
Depending where you live, don't forget to insulate lines. Less heat/cold loss.
 
Hummm, I’ll have to keep that in mind...it does have to run through crawl space area, not directly up and down to get to the fish room
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.7%
  • Fish or coral food

    Votes: 5 5.5%
  • Test kits or reagents

    Votes: 9 9.9%
  • Filter media or replacement fleece

    Votes: 5 5.5%
  • RO/DI filters or supplies

    Votes: 14 15.4%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.0%
  • I keep a backup of everything

    Votes: 24 26.4%
  • Other (Post in the comments)

    Votes: 7 7.7%
Back
Top
Home
Post thread…
Market
What's new