Recirculating CO2 Scrubbing Skimmer Caps

[Projects with Sam]

I just revamped the page and product listing. Also I've provided a better description of how it works. Check it out if you're interested; let me know if you have any questions.

https://parlaquatics.com/collections/skimmer-caps-mods
This key provides a guide for the sizes:

90mm	AquaMaxx Bullet 2 Hang-On Back Skimmer
142mm	CADlights PLS-150
160mm	Simplicity 240 DC
162mm	Bubble Magus Curve 7 Elite
162mm	Reef Octopus Classic 150
167mm	designed
171mm	Akula 160
191mm	Maxspect SK400
217mm	Dalua GW-17
Custom / New sizes	If your skimmer is not listed, contact me through your account email here or in R2R and I can add it.

 

[j90ramos]

Simplicity 120 DC price?

 

[Projects with Sam]

Simplicity 120 DC price?

I price them based on their size. larger ones are more expensive because of the extra time and plastic needed to make them. If the cap on the skimmer is similar to an existing size I have the price will be similar too.

 

[EeyoreIsMySpiritAnimal]

So for the Reef Octo, would you leave one air hole open to room air and attach the tubing to the other? Or is only one hole used? Trying to figure out if the skimmer will get enough air with only the line from the scrubber.

 

[Projects with Sam]

So for the Reef Octo, would you leave one air hole open to room air and attach the tubing to the other? Or is only one hole used? Trying to figure out if the skimmer will get enough air with only the line from the scrubber.

I would plug one hole. If extra air is needed by the skimmer, it will pull the air through the weep holes at the bottom of the soda lime so the CO2 scrubbing benefits are still attained. @StatelineReefer put a solenoid on the extra port of his and had it opening to let in fresh air when his pH was high.

 

[StatelineReefer]

So for the Reef Octo, would you leave one air hole open to room air and attach the tubing to the other? Or is only one hole used? Trying to figure out if the skimmer will get enough air with only the line from the scrubber.

Remember the air going through most skimmer silencers is restricted more than this setup. Volume should be fine for anything smaller than a coffee table.

 

[EeyoreIsMySpiritAnimal]

Remember the air going through most skimmer silencers is restricted more than this setup. Volume should be fine for anything smaller than a coffee table.

Wait, so the tubing doesn't go from the scrubber to the silencer?
(I'm not convinced I even need a CO2 scrubber but am curious...)

And do you mean a skimmer smaller than a coffee table or a tank?

 

[StatelineReefer]

Wait, so the tubing doesn't go from the scrubber to the silencer?
(I'm not convinced I even need a CO2 scrubber but am curious...)

And do you mean a skimmer smaller than a coffee table or a tank?

Skimmer smaller than a coffee table.

I use the RO tubing as a joint between the 3d printed cap and the 3/8 id silicone tubing. The tubing goes to the skimmer air inlet, I bypass the silencer entirely.

 

[Projects with Sam]

I am using my silencer but don't need to. I just like seeing the bubbles. watch the video. :D

 

[EeyoreIsMySpiritAnimal]

I am using my silencer but don't need to. I just like seeing the bubbles. watch the video. :D

Thanks. Btw, I did watch the video before asking my questions but was still unsure since the camera didn't actually capture you putting the scrubber on the skimmer.

 

[Projects with Sam]

Thanks. Btw, I did watch the video before asking my questions but was still unsure since the camera didn't actually capture you putting the scrubber on the skimmer.

ahh. kk I need to do another video then!