:-) The documentation is still not very good . I like interacting with fellow reefers, particularly how they are using/intend to use the controller etc. Also, several other folks here lend a hand in support/answering question. Kudos to the community
Can you elaborate a bit, when you say it will not control 24 hour light cycle,
Electronics and software looks all good. Telemetry is disabled hence the skipping log, its fine. Your time is set at 8:30 PM , is that correct ?
You also mentioned manual dimming is working. Do you mean dimming from the slider in reef-pi ?
My time is 20:30 pm but i have 24 hour mode so it is 20:30 can this cause the problem. Another funny thing is, when i'am on 100% reverse i read aronud 4,6 volt (light should be of) and when i'am on 0% full light due to reverse i have near 10 volt. So my volt do not drop all the way to 0 and also not going to max 12v
Yes slider in reef-pi is working just fine going from no light to full light. i use a PCA9685 board hook up to a mosfet IRLB 8743. PWM signal from PCA9685 i connected to Gate on mosfet in between is a 1 Kohm resistor. PCA9685 is connected to Raspberry pi via SCL1, SDA1, GND and 5 vcc hope that gives some understanding.
the 0 and 100% effect is expected. When you say 0% pwm , it means no gating at all. In the 1.1 release I have added three additional UI fields to specify min, max and start. You should set start to 1. That will tell reef-pi to never set the pwm value to 0 , instead set 1 as the lowest value , which in turn will give you close to 0 volt instead of 10 volt at 0%.
Heroic!! Well done!!This is the ongoing development thread of reef-pi, an open-source, affordable, modular DIY reef-tank controller based on Raspberry Pi. If you are trying to build a controller based on reef-pi, please check out the build guides at http://reef-pi.com. You can use this thread to seek help with your build or to stay updated with the latest development.
reef-pi provides following functionalities:
- Equipment control or power bars
- Digital timers to switch on/off equipment at periodic intervals.
- LED lighting control (24 hour cycle)
- Auto Top Off (based on photoelectric sensor or float switch)
- Temperature monitoring and control (switch on/off heater/cooler)
reef-pi source code and hardware schematics can be found on github.
- And several other features like camera controls (periodic image capture and upload on google drive), telemetry (dashboard and alerting based on sensor values using adafruit.io) etc.
--------------------------- Original thread start ---------------------
Hello friends,
I am starting a master thread for a DIY reef tank controller that is based on all opensource software and hardware. I had started with this project with following goals:
- Build an opensource software and hardware based reeftank controller that anyone can use and hack
- Keep the controller well tested against a set of standard equipment I use, while make it possible for other equipment to be used
- Maintain my own tank build threads and their evolution, backed by this controller.
- Learn electronics and reef keeping along the way (I am biologist by education & software engineer by occupation)
Following are the details of what I have developed & tested till now:
Controller software:
- The main controller software is called reef-pi. It is written in go, its fast and performant. It used embd for hardware communication. It also runs a little web server which provides the UI for the controller. UI is written in React , and can be accessed from anything that has web browser. As of now, the reef-pi supports following things:
- AC 110/220 V socket on/off (uses optocoupled relays underneath). This is used to remotely switch on/off return pump, LED bulb, heater etc.
- 0-20 Volt DC PWM. This is used to control things like dimmable LEDs, DC pumps. I use it to control my Kessil A80, A360. As well as a 5V DC pump (i use it as wave maker in one of my pico with SPS). PWM is done using PCA9685 breakout board from adafruit. This board supports 16 channels. I am using only 5 at max, as of now.
- Analog sensor support using MCP3008 analog to digital converter. This supports 8 channels. i.e. I can use up to 8 sensors/probes. As of now, I have only tested temperature sensor with it.
Other than the following basic hardware/equipment support, the controller software provides following additional features:
- Setting up daily/weekly/monthly scheduled jobs. Like turning on/off certain equipment. I use this feature to run my AC20 HOB filter nightly.
- Setting up dusk-to-dawn like lighting using PWM. The UI gives 12 vertical slider based 0-24 hours (each slider representing 2 hours gaps). I combine two of these two control the kessil LEDs.
- Authentication using Google OAuth. Since the whole controller runs on raspberry pi and provides an web frontend, security of one of my concern. To mitigate this, I have added google authentication support, which when configured will allow only certain users to log in (email specified in the configuration value).
This is the summary of the core controller software and what features it has as of now. I am constantly writing/improving things around it. As of now, I have two reef tank powered by this. I 'll have seperate threads on the individual builds that will include the housing and ancillary hardware in nano-reef.com, as my tank build threads are there, but I'll share all the controller specific common bits here, including UI screen shots, and tank pics :)
Wiring sounds alright then. Let me cross check if the mosfet has a power drop ..
Thank you. reef-pi came a long way since then :-) . I'll update the front page with 1.0 release screen shots. We have better UI and documentations now :-)
