RO DI - PPM

  • Thread starter Thread starter joelat
  • Start date Start date
  • Tagged users Tagged users None

joelat

Community Member
View Badges
Joined
Feb 1, 2023
Messages
51
Reaction score
18
Location
United Kingdom
What state or country do you live in
United Kingdom
Rating - 0%
0   0   0
Hi All, I have started making my own RO water, Currently using 4 stage filter including DI resin finter. But i am not getting 0 PPM when filtered. I am getting around 0.1 - 0.15 ppm. To get 0 ppm can i add dechlorinator/Prime or would the difference be negligible? Thanks in advance.
 
The meters on my system do not read that low so if my water is less then 0.5 it is going to read 0
 
My meter reads lower than that I don’t know how accurate it is though, my knowledge on this was that it should always be as close to 0 as possible. I don’t know what The negatived are for the tank if there is still some trace above 0 ppm reading or if readings under a certain level would make a negligible difference in terms of long term negatives for the tanks
 
My meter reads lower than that I don’t know how accurate it is though, my knowledge on this was that it should always be as close to 0 as possible. I don’t know what The negatived are for the tank if there is still some trace above 0 ppm reading or if readings under a certain level would make a negligible difference in terms of long term negatives for the tanks

What meter are you using (brand and model)? Is it an inline meter, or something testing the done water once it is collected (which can easily rise due to CO2 from the air and other trace contaminants).

0.1 ppm TDS, if accurate, is adequate and ready to go.

I would NOT add Prime to it for any reason.
 
What meter are you using (brand and model)? Is it an inline meter, or something testing the done water once it is collected (which can easily rise due to CO2 from the air and other trace contaminants).

0.1 ppm TDS, if accurate, is adequate and ready to go.

I would NOT add Prime to it for any reason.

It is just one I picked Up from amazon, I can’t see a brand name on it. It is one you dip in the collected water. I will see if i can cross check with another meter to see if it is accurate. If so i will leave it at 0.1 - 0.15 would adding a 2nd DI chamber benefit me or again for the difference it would make should i just leave it?
 
It is just one I picked Up from amazon, I can’t see a brand name on it. It is one you dip in the collected water. I will see if i can cross check with another meter to see if it is accurate. If so i will leave it at 0.1 - 0.15 would adding a 2nd DI chamber benefit me or again for the difference it would make should i just leave it?

So it is a stand alone TDS meter. Be certain you are reading the values and units correctly. A very good (and usually expensive) conductivity meter can read 0.1 ppm TDS, but most cheap meters hit a limit at 1 ppm TDS. The Hanna DIST 1, for example, can only read 0 or 1 ppm TDS at its lower limit.

https://www.hannainst.com/hi98301-dist-1-tds-ppm-tester.html
If the 0.15 ppm TDS is correct and the true value is not 15 ppm TDS, then the water is fine, and it may not be able to read any lower anyway.
 

TOP 10 Trending Threads

HOW DO YOU HANDLE HOLIDAY DECORATING AROUND YOUR REEF?

  • I decorate the tank or stand

    Votes: 1 4.5%
  • I decorate AROUND the tank or stand

    Votes: 4 18.2%
  • I add one small seasonal touch but keep it very basic

    Votes: 0 0.0%
  • I take a holiday photo, but don’t decorate the space

    Votes: 0 0.0%
  • I leave the reef area as it is

    Votes: 13 59.1%
  • We don’t decorate for the holidays

    Votes: 4 18.2%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new