Stray voltage - help!

Fishingandreefing

2500 Club Member
View Badges
Joined
Nov 7, 2019
Messages
3,839
Reaction score
1,798
What state or country do you live in
Maryland
Rating - 0%
0   0   0
So it’s 19v stray voltage I need to be concern? I recently lost some corals and didn’t know what caused it so I checked.

even though I shut off everything, it still reading 10v

I turned them off one by one and found the following:

2 jebao wavemakers 4v
Octo skimmer 5v
Return pump 1v

so what’s next?

4E533675-958E-41F7-974B-A2B2B121BD88.jpeg
 
Did you unplug everthing near the tank including lighting and any controllers or monitors?
 
Did you unplug everthing near the tank including lighting and any controllers or monitors?
So I guess even though they’re not touching water still affecting the range? My 120g which sits about 3 feet away has a low reading of 7v
 
What I am curious is what would be the acceptable range
 
What I am curious is what would be the acceptable range

I was just doing research on this and i'm seeing anything over 40 to 50v is cause for concern but I'd rather have next to none.
 
Sounds more like induced rather than stray voltage somewhere. Very normal at those levels though i would really doubt it is cause of any issues.
 
I agree rather have none as well but it seems like everything you put in there add a few voltages. Make sure you guys check yours too

I hope my level is acceptable lol
 
Anyone else? I am not too worry if my tank is doing good but is not.

I checked all my other tanks and they’re floating at around 15-17v
 
If you want 0 volts in your tank use a grounding probe for induced voltage created by submersed pumps and open lamps to your aquarium. Before plugging in the probe make sure your receptacle is truly grounded. I have seen grounding type receptacles not have a grounding conductor attached, so the home owner thought they were protected, when they were not. It is a good idea to plug all 120v equipment into a GFCI receptacle.
 
Use a grounding probe.

I got hit one time by a broken UV lamp. Then hit again by a cheap powerhead in the sump. still haven’t installed the probe and I need to now that I’m reading this
 
I will have to check mine when I get home. Where are you checking it In the sump? Also if you do use a ground probe make sure you have everything on a GFCI circuit. I have everything split between two different GFCI circuit outlets.
 
If you want 0 volts in your tank use a grounding probe for induced voltage created by submersed pumps and open lamps to your aquarium. Before plugging in the probe make sure your receptacle is truly grounded. I have seen grounding type receptacles not have a grounding conductor attached, so the home owner thought they were protected, when they were not. It is a good idea to plug all 120v equipment into a GFCI receptacle.
I do have a ground probe plugged into the outlet. The test was done without it
 
I will have to check mine when I get home. Where are you checking it In the sump? Also if you do use a ground probe make sure you have everything on a GFCI circuit. I have everything split between two different GFCI circuit outlets.
I don’t but it’s on my list to get them
 

TOP 10 Trending Threads

WHAT KIND OF REEFING DEAL ARE YOU HOPING TO PICK UP THIS BLACK FRIDAY?

  • A whole new aquarium or complete system

    Votes: 4 15.4%
  • Lighting, pumps, or other major equipment

    Votes: 4 15.4%
  • Controllers, testing, dosing, or automation gear

    Votes: 2 7.7%
  • Dry goods and restocks, like salt, media, or food

    Votes: 2 7.7%
  • Corals! Must...Have...CORALS!!!

    Votes: 6 23.1%
  • Fish or other livestock

    Votes: 1 3.8%
  • Rock, sand, or other aquascaping supplies

    Votes: 1 3.8%
  • I’m browsing, but don’t have a specific target

    Votes: 4 15.4%
  • I’m not shopping for reef deals this year

    Votes: 1 3.8%
  • Other (Post in the comments)

    Votes: 1 3.8%
Back
Top
Home
Post thread…
Market
What's new