SYoung's IM100 EXT Build Thread

Syoung

Active Member
View Badges
Joined
Sep 15, 2017
Messages
122
Reaction score
55
Location
California
What state or country do you live in
California
Rating - 100%
1   0   0
Hey reefers, after a long (6+ year) break I'm finally ready to get back into the hobby. Previously I ran an IM 25G Lagoon built into an entertainment center, and had a blast. I did run into issues with the lack of water volume and accessibility, so I'm hoping to fix both in this build.

Delivery from IM



Build:
- IM100 EXT
- IM APS Stand
- Sump: RFS-39 - Potentially modified

Filtration:
- Skimmer: Akula UKS-160
- Reefmat 500
- Very interested in using a roller mat rather than filter socks, but I need to modify the RFS-39 sump
- Refugium (TBD light)
- Lifeguard 25W UV

Control:
- Apex A3

Lighting:
- (2) AI Hydra 32HD

Flow:
- MP40
- Dual Sicce Syncra SDC 6.0 return pumps
- (Tentative) AI Orbit 4 Gyre Pump

Hoping to get some feedback before I make too many mistakes! Especially as I try to modify the sump for the Reefmat.

20260903_113742.jpg
20260903_202922.jpg
 
Welcome back from hiatus, and good luck with your build!
 
But most importantly, I had to set up a water change station to support ~150 gallons of total water volume.

Here's the station I just finished:
20260907_120252.jpg


It's dual 32 gallon containers, the left is freshwater fed from the RODI unit and the right is saltwater. Unfortunately I made a mistake and didn't include a valve to the saltwater return. I'll fix that next week!

The plan is to use this station to pump saltwater ~50' to where the tank is. Hopefully with a Sicce Syncra SDC 6.0 it'll be powerful enough.

RODI Water
Saltwater Mixing


20260906_200142.jpg
 
First question:

Has anyone run into the impeller area of the Sicce Syncra SDC 6.0 leaking? It's very slow, but haven't been able to solve it. I've confirmed the O-Rings are in place.

20260907_105152.jpg
 
Following along!
 
Made some progress this weekend.

1) Drilled out and installed a ball valve on the saltwater return for the water change setup. Now I'm able to fully control where water flows and how quickly.

2) Moved the tank into position with some friends. Not too heavy! We had 3 total but could've done it with just two of us. It's looking pretty great. It's tall with the APS leveling stand, but not too bad. One of the cats has been very curious 👀.

20260913_193732.jpg


3) Modified the sump to accept the Reefmat 500 roller mat. I didn't want to have to change and wash socks repeatedly so I committed to modifying. I think it went well, but won't know until I start flowing water.

I made a separate post to document the modifications here.
20260913_193747.jpg



Lots of progress! Still planning to modify the return to have a redundant return sending water back to the display through a Lifeguard 25W UV sterilizer. Not sure how exactly I'll do that yet, but it's progress.

Used Neptune A3 comes on Tuesday. There really isn't much room in the stand with this sump, so I'm currently unsure how I'll wire or fit an ATO reservoir. No room available outside the stand.
 
Following along as my IM 100ext was ordered end of August. My initial thought with the sump when it comes was to run the fliter balls a bit, run socks a bit, then fit in a Nature Dimensions N clear M with 1 extra extension. Interesting to see the reef mat addition. I am going to check out the modifcation link shortly
 
Hey reefers, after a long (6+ year) break I'm finally ready to get back into the hobby. Previously I ran an IM 25G Lagoon built into an entertainment center, and had a blast. I did run into issues with the lack of water volume and accessibility, so I'm hoping to fix both in this build.

Delivery from IM



Build:
- IM100 EXT
- IM APS Stand
- Sump: RFS-39 - Potentially modified

Filtration:
- Skimmer: Akula UKS-160
- Reefmat 500
- Very interested in using a roller mat rather than filter socks, but I need to modify the RFS-39 sump
- Refugium (TBD light)
- Lifeguard 25W UV

Control:
- Apex A3

Lighting:
- (2) AI Hydra 32HD

Flow:
- MP40
- Dual Sicce Syncra SDC 6.0 return pumps
- (Tentative) AI Orbit 4 Gyre Pump

Hoping to get some feedback before I make too many mistakes! Especially as I try to modify the sump for the Reefmat.

20260903_113742.jpg
20260903_202922.jpg
Congrats on the tank and new system. I have the same system on order. I have a rather mundane question: When the pallet arrives, did you take time to open the packing crates to check the load before the delivery truck left? I know IM suggests this, I'm just wondering if I can lift the top crates off to get to the tank to check it. Thanks.
 
Hey man - quick question. Did you think about skipping out on the lower leveling portion of the APS stand at all? I just built mine, and see that it's optional. Obviously, the ability to perfectly level with those feet is great, but it'd look so much better where I'm planning on putting it without them. Just wondering if you had any doubts about using it.
 
Hey man - quick question. Did you think about skipping out on the lower leveling portion of the APS stand at all? I just built mine, and see that it's optional. Obviously, the ability to perfectly level with those feet is great, but it'd look so much better where I'm planning on putting it without them. Just wondering if you had any doubts about using it.
I thought about skipping it (and you definitely could), but I actually liked the extra height, it makes it nicely eye level when sitting down.

Without, there is no good way to level the stand except shims.
 
Ok, it's been a ton of work to get it going, but we're finally wet!

I love the build quality of IM tanks. However I'm slightly regretting the AFS sump. There is about ~2" of space on every side, and I have no room to put additional cabinets. It's extremely packed in there, and I'm keeping it ~8" off the wall.

Set up:
- A3 Apex
- (2) EB832 Energy Bars
- (1) DOS QD (for future)
- Pumps, Skimmer, Powerheads, Lights, and more
- Plumbed dual return pumps, and one goes through the 25W UV Sterilizer

20261026_153339.jpg


Here's the rear before putting it closer to the wall. I swear this is decently cable-managed, but it looks horrific. I tried to make everything accessible enough with 8" of room to remove and replace if needed. Lot's of zip ties and rolling up excess cable.

20261025_131100.jpg


You can see the UV sterilizer in the right of that image. Unfortunately I didn't take any better photos of it, but it's mounted to a wood stand in the corner behind a curtain.

Here's a closer view of my main panel. Added an AI Prime Fuge light for the refugium. Have a few more outlets if anything is needed in the future.

20261115_195001.jpg


Overall it's been up and running for a week or so, and seems to be solid! Working out a few kinks with the reefmat (I installed it backwards), but otherwise everything is going well.



20261115_184623.jpg
 
With the aquascape, I was really hoping to emulate the coolest tank I've seen: Chris's Algae Farm. Unfortunately I might not have a large enough tank for that much negative aquascape.

But I'm trying anyway. I built a PVC stand and a large rock structure from reef saver.

20261115_154439.jpg


20261115_160450.jpg


20261115_184627.jpg


Using AF Bio 1-2mm sand. I like it, seems fairly white and doesn't blow around too badly (but it does still blow). I need to adjust my flow to not move it too much.

I started the cycle with Fritz Turbostart 900 and AlgaeBarn Nitrocycle. The instructions were fairly sparse, and I was choosing the fishless rather than put in fish within 24 hours of Turbostart, so I also dosed ammonium chloride. I dosed enough ammonium to reach 2ppm, but also added the Nitrocycle, not realizing it seems to be an ammonia source as well.

It's been a week and I'm still well above 5ppm ammonia... Considering a water change soon. But nitrates are starting to creep up (at 0.3ppm).
 
Congrats on the tank and new system. I have the same system on order. I have a rather mundane question: When the pallet arrives, did you take time to open the packing crates to check the load before the delivery truck left? I know IM suggests this, I'm just wondering if I can lift the top crates off to get to the tank to check it. Thanks.
Seems like it depends on the shipper. My shipper wouldn't wait. And IM's instructions are contradictory in two places.

But talking to Brian it does seem that if you open quickly and see an issue, there will be no problems getting a replacement.

Opening was pretty easy, just need a utility knife and a flathead screwdriver.
 
Once I get this cycle under control, here's my first draft stock list. To be added over at least a year or more.

- (2) Ocellaris Clownfish
- McCosker's Flasher Wrasse
- Lubbock's Fairy Wrasse
- Flame Hawkfish
- Mandarin dragonet (1+ year or later)
- Royal gramma
- Tailspot Blenny
- Yellow Watchman Goby
- White-tail Bristletooth Tang

Planning mostly acropora or euphilia corals. Want to stay completely away from GSP, pulsing xenia, mushrooms, or anything that could propogate and tank over the tank! Trying to avoid teardowns.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new