Time to replace DOS head?

  • Thread starter Thread starter Huff747
  • Start date Start date
  • Tagged users Tagged users None

Huff747

Valuable Member
View Badges
Joined
Jul 18, 2017
Messages
1,241
Reaction score
1,024
Location
Glen Carbon, IL
Rating - 100%
3   0   0
I think my issue is perhaps that head(s) are wearing out but thought I'd try and get some confirmation. Tried a search but wasn't finding what I was looking for.

I use DOS for auto water changes and I noticed my salinity was going up. I was looking over the heads and running them manually and one of the heads seems to be getting air bubbles in the line at the head. I can see a full tube of water going into the head and then air bubbles in the line when coming out of the head. And when I stop manually priming I can see that the water falls back down the line.

So should I replace the head? I checked that the connections were tight. If I'm replacing one head should I replace both?

Thanks.
 
sounds like you just need to replace the peri tubing
 
Last edited:
You can definitely replace just the tubing. I buy it in bulk and replace every 6 months. I've yet to replace the roller head after 18 months. Imagine you can probably get the tubing from places like BRS too.

https://www.usplastic.com/catalog/i...=transactionals&utm_content=orderconfirmation

Couple more questions if you have a moment. I took a closer look at the tubing last night after work and looks like something I can do, did you use zip ties to hold the ends of the tubing on (looks like my DOS has them). And is that link the same place you ordered from? I'll probably order some, shipping is a bit annoying, but I didn't see an option at BRS.
 
It's a bit fiddly, but ultimately pretty simple. The tubing that I linked is the stuff I use (nominally 1/8" ID/1/4" OD). I just buy 10' at a time to help to mitigate the shipping cost (ends up around $5/foot with each foot being 3 replacements; so $1.75 versus $30 for a new head unit). You just pop the head off the pump, pry out the grey connectors (takes a bit of effort to work them out), snip off the old zipties, remove the old tubing, cut a new piece to length (use the old tube as a guide), press it back onto the barbs on the grey connector, replace with new zipties (the really small ones that you can get at HD), put a little o-ring lubricant onto the new hose and fit it back into the head unit. When replacing the head unit, make sure the + on the pump shaft aligns with the + on the roller assembly. You'll see what I mean when you take it off.

I imagine eventually a new roller assembly will be required, but even then it's not necessary to buy the full head unit as places like Avast sell the replacement roller for $9 - and it's better because it has four rather than two rollers.
 
Thanks again. I disassembled the head and pulled the tubing out to look for any holes and reassembled it last night (figured if I screwed it up I might have to buy a new head anyway) so all of that makes sense to me now. I'll probably order that same tubing you linked and replace it as I've been running it for a while.

Even last night after I reassembled everything I ran a calibration and it had to tweak it but when I ran the calibration again after the tweak it was on the money. Still figure it's wise to go ahead and replace the tubing. And thanks for the info on the o-ring lubricant. I wouldn't known to do that.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new