Tips on dosing Kalkwasser via your ATO

  • Thread starter Thread starter tenurepro
  • Start date Start date
  • Tagged users Tagged users None
Can you share where did you get that Jug... I have bought several from Amazon but after time they seem to leak. That only happens with the Kalk solution. With other solutions the ones that I have don't leak.

Thanks in advance...
 
Can you share where did you get that Jug... I have bought several from Amazon but after time they seem to leak. That only happens with the Kalk solution. With other solutions the ones that I have don't leak.

Thanks in advance...

I’m not sure what you used, but it’s best to avoid polycarbonate because the high pH will damage the polycarbonate.
 
I’m not sure what you used, but it’s best to avoid polycarbonate because the high pH will damage the polycarbonate.

Hummmmm... Thanks Randy.....

Didn't know that but you always hit the nail. jajajajajaj Thanks Buddy...

414OOyTCPTL.jpg
 
Hummmmm... Thanks Randy.....

Didn't know that but you always hit the nail. jajajajajaj Thanks Buddy...

414OOyTCPTL.jpg
You're welcome.

Happy Reefing. :)
 
Can you share where did you get that Jug... I have bought several from Amazon but after time they seem to leak. That only happens with the Kalk solution. With other solutions the ones that I have don't leak.

Thanks in advance...

I got my jugs from a local LFS. Same jugs they sell premixed saltwater in. I have been using these for about 2 years now. I’ve only had one leak in me but that was my fault, I accidentally laid it down on a sharp object, which poked through!
 
Hummmmm... Thanks Randy.....

Didn't know that but you always hit the nail. jajajajajaj Thanks Buddy...

414OOyTCPTL.jpg
I tried using this container. After just a few months I came home to Kalk water all over the living room. The plastic had cracked apart.
 
I just drill a couple holes in 5g bucket lid and glue in the tubing. It does seem to help stability to have the ATO drip doser pump
 
Anyone ever used a small powerhead in the ATO connected to an apex to stir the ATO/kalk?
 
Anyone ever used a small powerhead in the ATO connected to an apex to stir the ATO/kalk?
A still reservoir is actually better, the powerhead would mix in CO2 from the room air, which would cause the kalk to precipitate. Also increases chance of dosing a slurry to the tank, you just want the clear kalk solution being dosed
 
bumping this. Are you concerned with sucking up any precipitate from the bottom of the ATO jug?
 

TOP 10 Trending Threads

WHICH TYPE OF MISTAKE TAUGHT YOU YOUR MOST EXPENSIVE REEFKEEPING LESSON?

  • Moving too quickly or adding too much at once

    Votes: 7 35.0%
  • Skipping—or shortening—quarantine or dipping

    Votes: 5 25.0%
  • Buying the wrong equipment the first time

    Votes: 4 20.0%
  • Ignoring maintenance, warning signs, or redundancy

    Votes: 6 30.0%
  • Chasing numbers or making too many changes

    Votes: 3 15.0%
  • Choosing incompatible fish, corals, or invertebrates

    Votes: 3 15.0%
  • Poor aquascaping or tank-design decisions

    Votes: 1 5.0%
  • Failing to research an animal’s needs

    Votes: 1 5.0%
  • Trusting bad advice

    Votes: 3 15.0%
  • Doing something on the tank when you should've gone to bed

    Votes: 4 20.0%
  • Something else—tell us below

    Votes: 4 20.0%
  • I’m still waiting for my first expensive lesson!

    Votes: 2 10.0%
Back
Top
Home
Post thread…
Market
What's new