Turning old tank into sump, design and baffle help

CaptainKiwi

Active Member
View Badges
Joined
Dec 20, 2024
Messages
115
Reaction score
79
Location
Uk
Rating - 0%
0   0   0
1000023518.jpg


Calling all sump designers!

I have this old 40 gallon that used to be a freshwater tank, with dimensions 99cm long x 39 cm wide x 42cm tall, that I would like to turn into a sump. To be honest I have no idea where to start with this. My first question is what would be what is the best way to thoroughly clean this? I have ordered 4 pieces of 6mm float glass to use as baffles that is 2mm less wide then the tank to allow for silicone, and the pieces are all 30cm tall. I will use these filter sock holders:
1769341666692.png

I would like space for a large protein skimmer and a potentially equally as large refugium. The return will be pumped through a chiller and I would also like a UV sterilizer. Here is a drawing of how I was going to section everything off:

1769345616244.jpeg

The left view is on top and the right view is on the side

I would appreciate any thoughts and feedbacks on the design and also the methodologies on how to make the baffles work properly.
 
Here are my thoughts:

  • Cleaning: outside with a hose using a spray nozzle would be ideal
  • Are you sure you need a chiller? In the UK that doesn't seem necessary
  • Refugium and skimmer together can be tough, as whatever you have in the fuge may be sucked into the skimmer pump
  • This is the baffle design I'd recommend. This would prevent any "waterfall" noise and return bubbles that could result from your proposed design. If you have a way to incorporate an adjustable baffle between the middle and return sections, that might be helpful as well so you can control the water level for protein skimmer purposes.
  • I also included a photos of the sump I made for my frag system in case its helpful, and a link to more info on it is here: https://www.reef2reef.com/threads/tx’s-reef’s-zoo-med-50-gal-lowboy.1010910/page-3

1769447425201.png



1769447506166.png
 
Here are my thoughts:

  • Cleaning: outside with a hose using a spray nozzle would be ideal
  • Are you sure you need a chiller? In the UK that doesn't seem necessary
  • Refugium and skimmer together can be tough, as whatever you have in the fuge may be sucked into the skimmer pump
  • This is the baffle design I'd recommend. This would prevent any "waterfall" noise and return bubbles that could result from your proposed design. If you have a way to incorporate an adjustable baffle between the middle and return sections, that might be helpful as well so you can control the water level for protein skimmer purposes.
  • I also included a photos of the sump I made for my frag system in case its helpful, and a link to more info on it is here: https://www.reef2reef.com/threads/tx’s-reef’s-zoo-med-50-gal-lowboy.1010910/page-3

1769447425201.png



1769447506166.png
Thanks for the input!

Cleaning - apparently a vinegar solution is really good for cleaning? Or is a hose pipe and a scrubber good?

Chiller - absolutely I need one, unfortunately I lost my last fish to 32 degree (celcius) water last summer while I was away on holiday. It's a mix of the new highs of heat we seem to be reaching every year (yay global warming) as well as my house being very very good at letting heat in through glass and keeping that heat in.

Sorry if my diagram wasn't clear but the filter socks and skimmer is in one section, followed by the under/over into a refugium and the another under/over into the return, almost exactly like yours but with the under/over the other way around (so portioned into 3 sections).

May I ask the heights of the baffles for each stage and how you chose them?
 
Thanks for the input!

Cleaning - apparently a vinegar solution is really good for cleaning? Or is a hose pipe and a scrubber good?

Chiller - absolutely I need one, unfortunately I lost my last fish to 32 degree (celcius) water last summer while I was away on holiday. It's a mix of the new highs of heat we seem to be reaching every year (yay global warming) as well as my house being very very good at letting heat in through glass and keeping that heat in.

Sorry if my diagram wasn't clear but the filter socks and skimmer is in one section, followed by the under/over into a refugium and the another under/over into the return, almost exactly like yours but with the under/over the other way around (so portioned into 3 sections).

May I ask the heights of the baffles for each stage and how you chose them?
vinegar is ok for cleaning, I prefer citric acid because it smells better

got it on the chiller, I assume you're not big on air conditioning in your locale (and that's totally fine)

I wouldn't want the skimmer in the first chamber in your diagram because the water level will not be consistent, which is necessary to proper skimmer functionality. the baffle design i proposed would allow you to have the skimmer in the first or second chamber.

The heights of the baffles isn't overly relevant - for the baffles that allow water under them, the higher the better. For the ones that allow water over them, you decide the height of the baffle by the desired water level. Skimmers generally want ~9 inches of water or so. That's part of why I recommend an adjustable baffle between chambers 2 and 3 so you can change the water level as desired. The only real considerations for baffle height / water level are 1. skimmer operation and 2. ensuring there is enough vacant volume such that if your return pump fails for any reason, the sump can handle all overflow from your display.
 
Last edited:
vinegar is ok for cleaning, I prefer citric acid because it smells better

got it on the chiller, I assume you're not big on air conditioning in your locale (and that's totally fine)

I wouldn't want the skimmer in the first chamber in your diagram because the water level will not be consistent, which is necessary to proper skimmer functionality. the baffle design i proposed would allow you to have the skimmer in the first or second chamber.

The heights of the baffles isn't overly relevant - for the baffles that allow water under them, the higher the better. For the ones that allow water over them, you decide the height of the baffle by the desired water level. Skimmers generally want ~9 inches of water or so. That's part of why I recommend an adjustable baffle between chambers 2 and 3 so you can change the water level as desired. The only real considerations for baffle height / water level are 1. skimmer operation and 2. ensuring there is enough vacant volume such that if your return pump fails for any reason, the sump can handle all overflow from your display.
What is the best way to make an adjustable height baffle? Also if I only have 4 pieces of glass, what would be your recommended setup to have a skimmer section and refugium section?
 
What is the best way to make an adjustable height baffle? Also if I only have 4 pieces of glass, what would be your recommended setup to have a skimmer section and refugium section?
you'd need to use acrylic or some other material that is easier to cut than glass for the adjustable height baffle, I have a photo example and product link below

You can have the skimmer in chamber 1 if you design the baffles the way I proposed, which will have the 1st chamber water level set to a fixed height.

https://www.jaxracks.com/product-page/single-sock-refugium-baffle-kit-40-gallon-breeder
1769457258241.png

1769457291869.png
 
you'd need to use acrylic or some other material that is easier to cut than glass for the adjustable height baffle, I have a photo example and product link below

You can have the skimmer in chamber 1 if you design the baffles the way I proposed, which will have the 1st chamber water level set to a fixed height.

https://www.jaxracks.com/product-page/single-sock-refugium-baffle-kit-40-gallon-breeder
1769457258241.png

1769457291869.png
Ahhhh ok, that makes sense, I really appreciate the advice! I will use the design you suggested, put the skimmer in the first section with the intake, have the big refugium and I really like putting filter floss between the over/under so the inverts/fish I put in the fuge cant go in and out!

So from my understanding, the first baffle in each section basically sets the water height for that section and keeps it fixed, and the second one is there as the bubble trap right?
 
Ahhhh ok, that makes sense, I really appreciate the advice! I will use the design you suggested, put the skimmer in the first section with the intake, have the big refugium and I really like putting filter floss between the over/under so the inverts/fish I put in the fuge cant go in and out!

So from my understanding, the first baffle in each section basically sets the water height for that section and keeps it fixed, and the second one is there as the bubble trap right?
correct! Also, having the first baffle be an "over" creates some surface movement and prevents biofilm.
 
1000023518.jpg


Calling all sump designers!

I have this old 40 gallon that used to be a freshwater tank, with dimensions 99cm long x 39 cm wide x 42cm tall, that I would like to turn into a sump. To be honest I have no idea where to start with this. My first question is what would be what is the best way to thoroughly clean this? I have ordered 4 pieces of 6mm float glass to use as baffles that is 2mm less wide then the tank to allow for silicone, and the pieces are all 30cm tall. I will use these filter sock holders:
1769341666692.png

I would like space for a large protein skimmer and a potentially equally as large refugium. The return will be pumped through a chiller and I would also like a UV sterilizer. Here is a drawing of how I was going to section everything off:

1769345616244.jpeg

The left view is on top and the right view is on the side

I would appreciate any thoughts and feedbacks on the design and also the methodologies on how to make the baffles work properly.

What is the best way to make an adjustable height baffle? Also if I only have 4 pieces of glass, what would be your recommended setup to have a skimmer section and refugium section?

All great suggestions by @TX_REEF .

If you do decide to use acrylic for the adjustable baffle, make sure to leave some room for the acrylic to swell, on either side of the tank. In case you were wondering, acrylic does swell when left submerged in water and I have seen it crack tanks as a result.
 
correct! Also, having the first baffle be an "over" creates some surface movement and prevents biofilm.
Thanks man, really appreciate all the info!

All great suggestions by @TX_REEF .

If you do decide to use acrylic for the adjustable baffle, make sure to leave some room for the acrylic to swell, on either side of the tank. In case you were wondering, acrylic does swell when left submerged in water and I have seen it crack tanks as a result.
Noted, never would have thought acrylic would do that!
 

TOP 10 Trending Threads

HOW DO YOU HANDLE HOLIDAY DECORATING AROUND YOUR REEF?

  • I decorate the tank or stand

    Votes: 1 3.4%
  • I decorate AROUND the tank or stand

    Votes: 4 13.8%
  • I add one small seasonal touch but keep it very basic

    Votes: 0 0.0%
  • I take a holiday photo, but don’t decorate the space

    Votes: 0 0.0%
  • I leave the reef area as it is

    Votes: 20 69.0%
  • We don’t decorate for the holidays

    Votes: 4 13.8%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new