Whats this? A dosing pump for ants? Probably smallest peristaltic pump.

  • Thread starter Thread starter Tavero
  • Start date Start date
  • Tagged users Tagged users None
Does the liquid run down the lines, that you need to fill then?
I dont understand that question.

1/3mm tubing contains 1ml volume per 20-30cm. So if i mix a new supplement solution i need to let the pump run for a few minutes or it wouldnt dose anything foar a few days until the solution reaches the tank.
 
I mean when the pump doesn't run, are the lines empty after a while due the gravitiy.
That the lines are needed to be purged after a solvent change is clear.

Anyway I ordered some stuff for that type of project. ESP, thermometer, Clock, three color e-paper display, card reader, same tiny pumps, stepper driver.
I hope I can combine the temperature and some other things (calendar like) on the display.
 
I mean when the pump doesn't run, are the lines empty after a while due the gravitiy.
That the lines are needed to be purged after a solvent change is clear.

Anyway I ordered some stuff for that type of project. ESP, thermometer, Clock, three color e-paper display, card reader, same tiny pumps, stepper driver.
I hope I can combine the temperature and some other things (calendar like) on the display.
Lines in a dosing system are never empty. The peristaltic pump is blocking them even if it is off.

I had a bacterial bloom an a parcial crash in my display tank last week so I didn't have any free time. I will post a guide and the code when I'm over it.
 
Thanks for the information, that these pumps can block the lines.
As I said I experienced in a differend project, that DC pumps not always block the lines.

Take your time with your tank, that is more important. I got a lot of stuff but not the pumps so far. I hope I can somehow copy your project with ChatGPT. Your idea to connect to the pumps via IP address is great. Otherwise I wouldn’t go for it.
 
Thanks for the information, that these pumps can block the lines.
As I said I experienced in a differend project, that DC pumps not always block the lines.

Take your time with your tank, that is more important. I got a lot of stuff but not the pumps so far. I hope I can somehow copy your project with ChatGPT. Your idea to connect to the pumps via IP address is great. Otherwise I wouldn’t go for it.
You can try with ESPHome or Tasmota. I’m not sure about others, but I have an IT background so I find them quite simple.
 
I'm trying to get it somehow functioning. It took me a while to get to this point.
I have the temperature on the e-Paper display. I have a wifi setting to adjust the offset and factor if I need to "calibrate" the temperature. I can set also a temp min and max value for the color. Between T min and max the value is displayed black, otherwise it is red.

Next would be integrating the pumps and a SD card reader for temp logging and I want to put also a calendar on the lower part of the display.

How did you connect the pumps with the driver? Did you put also some resistors or capacities between some pins? At least ChatGPT want me to do this.

Best



1000150729.jpg
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 17.7%
  • Fish or coral food

    Votes: 5 5.2%
  • Test kits or reagents

    Votes: 10 10.4%
  • Filter media or replacement fleece

    Votes: 5 5.2%
  • RO/DI filters or supplies

    Votes: 15 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 12 12.5%
  • I keep a backup of everything

    Votes: 25 26.0%
  • Other (Post in the comments)

    Votes: 7 7.3%
Back
Top
Home
Post thread…
Market
What's new