Xr30 g4 burnt capacitors

  • Thread starter Thread starter ntec
  • Start date Start date
  • Tagged users Tagged users None

ntec

New Member
View Badges
Joined
May 5, 2020
Messages
14
Reaction score
1
Location
Canada
What state or country do you live in
Canada
Rating - 0%
0   0   0
I have a radion g4 that has several caps that burnt off which is not shown in the pics. Anyone know the exact value of the cap circled in the pics so I can order replacements.

IMG_4281.jpeg
 
Last edited:
Usually the numbers are on them, take one off and turn it over, but, they may be generic
 
Usually the numbers are on them, take one off and turn it over, but, they may be generic
These caps don't have numbers on them and I don't have a lcr meter to properly check value as I only have a fluke meter.
 
My lamp is short circuited, when opened i found those capacitors burned, any news?
 
mg, what makes you think those caps are burned?
 
mg, what makes you think those caps are burned?
I found two burned caps, exactly as the picture, the power supply shut down automatically as soon as I connect the lamp, i removed those two burned caps now the lamp works again without the caps but want to replace them, they are there for something, maybe these caps with the coil produce some frequency for the LEDs, don’t know. i have the equipment to remove one good cap and test, be back soon. Photo attached…

IMG_1323.jpeg
 
Ok, here my results…

2.3 micro farads
 

Attachments

  • IMG_1325.jpeg
    IMG_1325.jpeg
    198.9 KB · Views: 19
  • IMG_1326.jpeg
    IMG_1326.jpeg
    196.4 KB · Views: 26
  • IMG_1327.jpeg
    IMG_1327.jpeg
    174.8 KB · Views: 24
  • IMG_1328.jpeg
    IMG_1328.jpeg
    223.4 KB · Views: 49
  • IMG_1331.jpeg
    IMG_1331.jpeg
    53.9 KB · Views: 40
Ok, the top one is burnt. Don't know about the one below it but you could replace them both. You can get them from Digi-key. Search on 2.2uf capacitor. 2.3 is not a standard size. That will get you close, however you will need the correct physical size to fit and the voltage.
 
Ok, capacitors replaced.... and is alive!!!!

Yes, changed to 2.2 uf ceramic, small ones, just fit inside.

I had two damaged, the one below the burned one on the picture was ok, there is another one at the opposite side of the board that was damaged as well, replaced both, the short circuit was fixed, now seems everything is ok.

1751656468357.png
 
Last edited:

TOP 10 Trending Threads

HOW MUCH DOES A FISH’S FEEDING REQUIREMENTS AFFECT YOUR STOCKING DECISIONS?

  • A lot! - I avoid fish that require frequent or specialized feeding

    Votes: 14 30.4%
  • Quite a bit, but an automatic feeder can change my answer

    Votes: 6 13.0%
  • It depends on whether my nutrient export can handle it

    Votes: 6 13.0%
  • It depends on how badly I want the fish

    Votes: 11 23.9%
  • Not much. I’m willing to adjust my routine

    Votes: 9 19.6%
  • Not at all. Feeding demands don’t limit my stocking choices

    Votes: 8 17.4%
  • I usually learn about the demanding feeding schedule after buying the fish!

    Votes: 2 4.3%
  • I haven’t really considered this before

    Votes: 4 8.7%
  • Something else (see my comments in the thread)

    Votes: 1 2.2%
Back
Top
Home
Post thread…
Market
What's new