1/4 RO bulkhead fitting question. FW container

  • Thread starter Thread starter Dondante
  • Start date Start date
  • Tagged users Tagged users None

Dondante

Well-Known Member
View Badges
Joined
Dec 7, 2018
Messages
559
Reaction score
254
What state or country do you live in
Alabama
Rating - 0%
0   0   0
I drilled this so that it would screw into the container. Loaded with plumbing tape and screwed tight. Will I need a gasket? Of so where would I find one locally? Should I just leave it? Think it will leak the way I have it after Time?
20200518_002119.jpg
20200518_002136.jpg
 
Plummers tape won’t do anything to seal that. You need a gasket. If you don’t have a gasket I would try to find one at Ace or truevalue. Worse case seal it with plumbers putty or silicone.

Also I would reverse it. Put the nut side on the outside of the barrel.
 
I don’t believe those bulkheads are meant to be water tight... at least that’s what I was told from BRS when I asked about them. you will probably have to DIY something like just siliconing it in place
 
I don’t believe those bulkheads are meant to be water tight... at least that’s what I was told from BRS when I asked about them. you will probably have to DIY something like just siliconing it in place
Only one issues with silicone and Brute trash cans, it doesn't stick. Ask me how I know, and how I ended up with 40G of water on my floor. lol
 
Only one issues with silicone and Brute trash cans, it doesn't stick. Ask me how I know, and how I ended up with 40G of water on my floor. lol
Then the OP is SOL and will have to come up with a different solution
 
You can always epoxy it in place if the silicone doesn't stick and you can't find a suitable gasket.

Provided you never have to remove the bulkhead - I've never had epoxy fail me.
 
You will definitely need a gasket, or some way to seal the flange side. I made one out of some silicone sheet that I had laying around, but silicone sealant will work fine also. It doesn't have to 'stick' to the can, it just acts as a gasket once cured. Just put silicone under the flange, install the bulkhead but don't tighten it down fully. Let the silicone completely cure and then fully tighten down the nut. Voila …. gasket. Putting Teflon tape on the bulkhead threads does nothing …. just increases the chances of breaking the nut.

B13DACAB-2380-4EDB-9B59-702D55B809BB.jpeg
 
Last edited:
I drilled a hole in a 5 gallon bucket and used a similar fitting. I put a small amount of silicone around the part that went through the hole before I screwed on the backside.
I did this probably 8-9 years ago and it's still water tight.
 
I may go buy some gasket making material. I actually threaded into the brute. Better safe than sorry. Off to Lowe's.
 
I've done this exact thing- in my case I used waterweld putty and it held for a few years. If you can find something to act as a gasket, that might be preferable if you don't want it to be permanent.
 
Found this at Lowe's. 1.99
20200518_141051.jpg
 
That should do. I have a set of hole punches but none big enough so i used a scrap of 3/4" copper pipe and a hammer to cut the hole, then just trim around the edge of the flange. Not pretty but works.
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 21 25.6%
  • I’d trust someone who knows my tank to choose

    Votes: 8 9.8%
  • I’d rather get a gift card and pick it myself

    Votes: 30 36.6%
  • I’d prefer gear or supplies instead

    Votes: 2 2.4%
  • Please don’t surprise me with livestock

    Votes: 21 25.6%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new