Cannot assign PAB for new Maxi doser

Discussion in 'GHL Advanced Technology' started by Mortie31, Dec 23, 2017.

  1. Mortie31

    Mortie31 Active Member UK Reef Club Member

    Joined:
    Apr 5, 2016
    Messages:
    316
    Likes Received:
    173
    Location:
    Uttoxeter. England
    Hello
    I cannot get my new Maxi doser to assign to my system, the doser is plugged in the connect lights are lit and the logo is blue, however when I click the assign devices button i can see the correct serial number, but the description is blank, for my other devices it says doser 2:1 etc. If I then check the tick box and continue, it disconnects as usual, then upon reconnecting the device is not assigned and in my list. I’ve been around this loop several times I’m in the new 1.03 gcc and 7.08 firmware. Am I doing some stupid or is there an issue? Hope you can help
    Paul
     
    Tristren likes this.
    Tags:

  2. Mortie31

    Mortie31 Active Member UK Reef Club Member

    Joined:
    Apr 5, 2016
    Messages:
    316
    Likes Received:
    173
    Location:
    Uttoxeter. England
    Bad timing to run into issues just at Xmas lol
     
  3. Jerel

    Jerel Active Member

    Joined:
    Oct 8, 2016
    Messages:
    285
    Likes Received:
    155
    Location:
    Upper Marlboro, Maryland
    You’ll need GCC 1.0.4, which has support for Doser Maxi.
     
    Marco@GHLUSA and Tristren like this.
  4. Marco@GHLUSA

    Marco@GHLUSA GHL Team R2R Supporter Platinum Sponsor

    Joined:
    Jul 27, 2016
    Messages:
    384
    Likes Received:
    220
    Location:
    Fort Myers, FL
  5. Mortie31

    Mortie31 Active Member UK Reef Club Member

    Joined:
    Apr 5, 2016
    Messages:
    316
    Likes Received:
    173
    Location:
    Uttoxeter. England
    Thanks chaps, have upgraded to this version and it recognised the doser, unfortunately the doser firmware update it needed after, didn’t work, but I’ll have another try tomorrow
     
  6. Marco@GHLUSA

    Marco@GHLUSA GHL Team R2R Supporter Platinum Sponsor

    Joined:
    Jul 27, 2016
    Messages:
    384
    Likes Received:
    220
    Location:
    Fort Myers, FL
    @Mortie31
    GCC 1.1.0.5 has been posted to the download section, included are firmware updates for both PL3 & PL4.
     
    Last edited: Dec 28, 2017
  7. Lasse

    Lasse Valuable Member R2R Supporter Reef Squad Leader R2R Excellence Award Reef Tank 365 Build Thread Contributor

    Joined:
    Mar 20, 2016
    Messages:
    1,753
    Likes Received:
    3,841
    Location:
    Källarliden 14 D Bohus, Sweden
    @Marco@GHLUSA I can´t find either 1.1.0.4 or 1.1.0.5 at the website

    Sincerely Lasse
     
  8. Marco@GHLUSA

    Marco@GHLUSA GHL Team R2R Supporter Platinum Sponsor

    Joined:
    Jul 27, 2016
    Messages:
    384
    Likes Received:
    220
    Location:
    Fort Myers, FL
    We've pulled offline and will will revisit tomorrow.
     
  9. Lasse

    Lasse Valuable Member R2R Supporter Reef Squad Leader R2R Excellence Award Reef Tank 365 Build Thread Contributor

    Joined:
    Mar 20, 2016
    Messages:
    1,753
    Likes Received:
    3,841
    Location:
    Källarliden 14 D Bohus, Sweden
    Thank you

    Sincerely Lasse
     
  10. Marco@GHLUSA

    Marco@GHLUSA GHL Team R2R Supporter Platinum Sponsor

    Joined:
    Jul 27, 2016
    Messages:
    384
    Likes Received:
    220
    Location:
    Fort Myers, FL
    Back up :)
     
  11. Lasse

    Lasse Valuable Member R2R Supporter Reef Squad Leader R2R Excellence Award Reef Tank 365 Build Thread Contributor

    Joined:
    Mar 20, 2016
    Messages:
    1,753
    Likes Received:
    3,841
    Location:
    Källarliden 14 D Bohus, Sweden
    @Marco@GHLUSA Avast still block the file we speak about earlier

    Sincerely Lasse
     
  12. coweyes298

    coweyes298 Active Member

    Joined:
    Jun 5, 2017
    Messages:
    374
    Likes Received:
    159
    Location:
    Los Angeles, Diamond Bar, CA
    Following. Have been using 1.1.0.4 for several days. Did some firmware update too. So far so good.
     
  13. Mortie31

    Mortie31 Active Member UK Reef Club Member

    Joined:
    Apr 5, 2016
    Messages:
    316
    Likes Received:
    173
    Location:
    Uttoxeter. England
    Success Marco and Matthias... FW and GCC updated to 7.09 and 1.05. Maxi doser is assigned, named correctly and is configured... now to calibrate it and get it working 5A9488DB-2F24-47DA-8D11-A191AAF8E945.jpeg
     
Draft saved Draft deleted

Share This Page

Loading...